What a Build Sheet Records — and Why Every Crawford Motor Has One
Share
A built motor is a few hundred decisions. Pistons, rods, bearings, clearances, gaps — each one chosen for a power target and a use. The build sheet is where those decisions are written down, per engine, before the motor leaves the shop. Every Crawford motor ships with one. This is what is on it, section by section, and what each section is for after the motor is in the car.
The identity block: which motor this is
The top of the sheet names the build: the spec tier, the application, and the foundation it was built on. For Crawford that foundation is always a brand-new OEM case — never a used block machined back to size, and no core is required or accepted. That matters to the rest of the sheet. Every measurement below it was taken against a case that started at known dimensions, not against wear nobody can fully account for. Why that policy exists is its own subject: why Crawford builds on brand-new OEM cases.
The components: what is inside
The sheet lists the parts the motor was assembled with. On a Crawford build that means CrawfordSPEC forged pistons made by JE Pistons, CrawfordSPEC connecting rods developed with Pauter Rods, and the bearings selected for that build — selected per journal position, not pulled from one box for the whole crank. Years later, when the motor needs a part or a decision, nobody guesses what is inside it. It is written down.
The measurements: the numbers the motor was set to
This is the heart of the sheet, and it is recorded per engine, not per design:
- Main and rod bearing clearances — measured journal by journal, set to the build's target. What those numbers control, and what happens at either end of the range, is covered in bearing clearances: what "blueprinted" means.
- Ring end gaps — filed per cylinder and sized for the boost the build will run. The failure modes in both directions are in ring gap for boost.
- Piston-to-wall clearance — set knowing how much a forged piston grows as it heats. This number is also why a built motor can sound different cold than it does warm.
- Deck height and thrust clearance — the piston's position relative to the deck, and the crank's end play. Small numbers. Real consequences.
A motor assembled from parts that merely fall inside a factory tolerance stack has none of this. The sheet is the difference between an engine that was measured and an engine that was assembled.
The ownership specs: what the numbers require of you
The sheet also carries the specs the motor lives under after delivery:
- The break-in schedule. Oil changes at 500 and 1,500 miles. Engine speed 2,000–4,500 RPM, varied — no sustained cruising, no full-throttle pulls. No more than 80% of target boost until break-in is complete. The full procedure is in the built-motor break-in guide.
- The oil the clearances were set for. Clearance and viscosity are a pair. The sheet records the pairing so the motor is never run on a guess.
- The first oil analysis. Mandatory, and a condition of the 1-year / 12,000-mile warranty. The analysis is read against the sheet: the clearances predict how the bearings should wear, and the report shows whether they are. How to read that report is in how to read an oil analysis.
What the sheet does for the life of the motor
It is the baseline. Every later oil analysis, every pressure reading, every question about how the motor is aging gets judged against the numbers it started with. Without the sheet there is no baseline — only opinions about a motor nobody measured.
It is the warranty record. If a question comes up under warranty, the conversation starts from the sheet: what was built, what it was set to, and whether the break-in and analysis the warranty requires were done. Numbers, not recollections.
It travels with the motor. A built engine with its build sheet is a known engine — to the next shop that works on it, and to the next owner if the car is sold. A built engine without one is a story.
What to ask any builder
Before you buy a built motor from anyone, ask to see a build sheet from a motor they have already delivered — redacted is fine. You are not checking their numbers. You are checking that the numbers exist: measured per engine, recorded, and handed to the customer. A builder who will not show you one has told you how the motor was built.
The motors built this way are the built EJ257 short block tiers — CSS 540 at $4,999 MSRP, CCR 660 at $5,599 MSRP, CRS 720+ at $5,999 MSRP — and the EJ257 long blocks built on them. Every one is assembled to order, on a new OEM case, and ships with its sheet.
Questions about a build: (855) 677-8243.
FAQ
Do I get the build sheet, or does the shop keep it?
You get it. It ships with the motor. Keep it with the oil analysis reports — together they are the engine's service record.
Are the clearances the same on every Crawford motor?
No. They are set to each build's target — its power, its use, and its oil — and recorded per engine. Two motors of the same spec tier can carry different numbers because they were built for different work.
Why does the sheet matter if the engine runs fine?
Because "runs fine" is not a measurement. The sheet is what lets you prove the motor is wearing the way it should — and it is where any warranty conversation starts.
Can the build sheet tell me what parts to order later?
Yes. The components inside the motor are listed on it, which is the point: nobody has to guess what is in the engine when it needs parts or machine work years from now.
Related reading: the head gasket is one of the specs the build sheet settles — bore, thickness, and finish. See the Cometic gasket guide for how those choices are made.
Related reading: the piston-to-wall line on the sheet is the one owners hear — piston-to-wall clearance: why a built motor is louder cold explains the number and the noise it makes.