Cometic Gaskets for Subaru: MLS Head Gaskets by Bore and Thickness
Share
A head gasket is not a commodity part on a built Subaru — it's a specification. Bore size has to match the block, and thickness is one of the numbers that sets your compression ratio and quench. Cometic builds multi-layer steel (MLS) and MLX head gaskets for the EJ and FA in the combinations builders actually spec, plus complete engine gasket kits around them. Crawford carries the line.
Crawford First: Our Own Installation Kits
Start where Crawford starts. Every Crawford built short block is assembled here on a brand-new OEM case, with its gaskets and seals specified and recorded on the build sheet — buy the motor and the sealing is already handled. Installing one yourself? Crawford's own EJ25 Short Block Installation Kit ($799.95; 2004–2006 at $799.99) and FA20DIT Installation Kit ($699.99) carry the complete gasket and seal set for the install, by application, EJ20/EJ25 Hybrid and FA20 versions included ($699.95–$799.99). That is the Crawford answer, and it comes first. The shelf below is for building or resealing a motor that isn't ours.
Head Gaskets: Pick Bore, Then Thickness
For the EJ257, the standard bore is 101mm, with 102mm and 102.5mm for overbored blocks. Thickness runs from .027" to .120" — the spread exists because deck height, piston protrusion, and target compression differ build to build. That choice belongs on the build sheet, not in a shopping cart guess: it's one of the measurements our build sheet post walks through.
- Cometic 101mm .040 inch MLS Head Gasket — STI 2007–2018 — $55.57, the common stock-bore spec; the same gasket runs .027" to .120" across the range at $55.57–$129.52.
- Cometic Version 2 .044in MLX Head Gasket, 101mm — STI 2007–2018 / WRX 2007–2014 — $108.47. MLX is Cometic's stopper-layer design for high cylinder pressure — the boosted application's gasket.
- Cometic 2.5L 102mm Bore .040 MLS Head Gasket — STI 2004–2021 — $58.34, for the first overbore.
- FA20 WRX owners: the 89.5mm gaskets are sold per side — left and right at $108.47 each (.032" at $82.14).
Complete Engine Gasket Kits
- Cometic Street Pro DOHC 101mm Complete Gasket Kit — STI 2004–2021 — $400.54. The full engine set with the MLS head gaskets included — one box for a complete reseal at stock bore.
- Cometic Complete Engine Gasket Kit, 101mm with .060 MLX — STI 2008–2018 — $472.94, with .028" and .052" versions at $413.97–$472.94 — the kit follows the head gasket spec you choose.
- Cometic Engine Gasket Kit, No Head Gasket — STI 2004–2021 — $279.89. For builders speccing their head gaskets separately: everything else, one kit.
Seals and the Small Gaskets
The rest of the line is the reseal shelf: camshaft seal set $45.43, valve cover gasket kits $26.49 a side, rear main seal $17.42, oil pan gasket $12.45, front crankshaft seal $7.40, thermostat gasket $5.27. None of it is glamorous; all of it is the difference between an engine that stays sealed and one that comes back apart. For OE-pattern replacements across the whole engine, the companion line is Fel-Pro.
One surface note, because it decides whether any MLS gasket seals: MLS needs a clean, correctly finished deck and head surface. A gasket can't fix a finish problem — that's machine work, and it's why the deck finish is recorded on the build sheet.
FAQ
MLS or MLX? MLS is the standard multi-layer steel gasket and covers most builds. MLX adds a stopper layer for higher cylinder pressure — big-boost builds take MLX.
How do I choose thickness? From the build: deck height, piston-to-deck measurement, chamber volume, and the compression ratio you're targeting. If those numbers aren't on paper yet, the gasket choice waits — it's a spec, not a guess.
Do I need the complete kit for a head gasket job? You'll disturb more than the head gaskets getting there. The complete kit costs less than the second parts order and the downtime — and every seal you touch should be replaced, not reused.
Can I reuse an MLS head gasket? No. MLS gaskets are single-installation parts — the embossed layers take their set on the first torque.