EJ257 Short Block Tiers Compared: CSS 540 vs CCR 660 vs CRS 720+
Share
Same three tiers as the long block line, without the heads. The Crawford built EJ257 short block is the bottom end only — block, crank, rods, pistons, bearings — built to order for 2004–2021 STI, and the same tiers fit the EJ255 in the WRX. This post is the decision: which tier, and why the price steps are where they are.
The general guide covers what a short block is and what the swap takes. The long block tier comparison covers the same three ratings with heads included. This one is for the buyer whose heads are good and whose bottom end is not.
What every tier shares
- Built to order in our shop from a brand-new OEM short block — no core required, no core charge, no used case bored out and put back in service.
- Fully blueprinted and assembled — clearances measured, set, and recorded, the same process covered in what "blueprinted" means on a build sheet.
- Upgraded race-proven bearings in every tier.
- CrawfordSPEC pistons sized for the OEM 99.5 bore. No oversized pistons, no bored-out case.
- Lead time is 2–4 weeks — built to order, final sale.
- 1-year / 12,000-mile warranty. Break-in is a condition of it: oil changes at 500 and 1,500 miles, 2,000–4,500 RPM varied, no sustained cruising or full-throttle pulls, no more than 80% of target boost until break-in is complete, and the first oil analysis is mandatory.
What a short block does not include: heads, and the gaskets and hardware to put it together. Budget the short block installation kit for your year — it carries the pieces that should be replaced new on install, down to break-in oil.
CSS 540 — the street tier — $4,999 MSRP
Rated to 450 whp (540 bhp). The step over stock is the pistons: CrawfordSPEC CSS forged pistons, made by JE Pistons — SCCA-approved and stamped accordingly — on the new OEM block with upgraded bearings.
This is the tier for a stock-location turbo car, a daily driver that gets driven hard, or a replacement for a failed stock bottom end that will not stay stock. The factory cast pistons are the weak point past 350 whp — the ringlands go first. The CSS removes that ceiling without paying for rods the build will never load.
CCR 660 — the rod tier — $5,599 MSRP
Rated to 550 whp (660 bhp). Two steps up: CrawfordSPEC CCR JE forged pistons, and CrawfordSPEC X-Beam billet rods developed with Pauter Rods — billet 4340 chrome-moly, longer than stock for a better rod ratio and smoother power delivery.
Between 450 and 550 whp, cylinder pressure stops being a piston problem and becomes a rod problem. Rotated turbo, E85, track days at real power — this is the tier. The $600 step over the CSS is cheaper than opening the motor twice.
CRS 720+ — the top tier — $5,999 MSRP
Rated to 600+ whp (720+ bhp) — the top of the Crawford line. CrawfordSPEC CRS FSR billet forged pistons: Forged Side Relief design, 100% CNC-machined from 2618-T6 bar stock, up to 32 grams lighter than a traditional forging, with 9310 steel wrist pins and a reduced skirt that cuts friction against the wall. CrawfordSPEC forged rods underneath.
Less reciprocating weight is less load on everything at high RPM. This tier exists for drag and serious track builds that live at the top of the tach. If the car will never see 600 whp, the CCR is the honest buy. If it will, nothing below this tier is.
Short block or long block?
Same tiers, same ratings, same internals. The difference is the top end.
- Your heads are known-good — inspected, no damage, no overheating history: buy the short block and keep them.
- Your heads are tired, damaged, or unproven: the long block includes the Crawford Essential Cylinder Head Service — inspection and prep of the heads you send — and built long blocks ship free.
One warning that applies either way: the tier does not save a bad tune or a contaminated oil system. After a failure, everything that shared oil with the old motor gets cleaned or replaced. The tune has to be a professional custom tune for your exact combination. For e-tuning, Crawford recommends Delicious Tuning.
Protect the new bottom end the same way regardless of tier: an Air Oil Separator to keep oil out of the intake charge, the break-in followed to the letter, and the oil analysis read when it comes back.
Questions on which tier fits your build: (855) 677-8243.
FAQ
What is the price difference between the tiers? CSS 540 is $4,999, CCR 660 is $5,599, and CRS 720+ is $5,999. The steps buy internals: forged pistons at the CSS, billet rods added at the CCR, and the FSR billet piston at the CRS.
Do I need to send a core? No. Every tier starts from a brand-new OEM short block. No core charge, no core return.
Does the short block include heads? No. A short block is the bottom end. If your heads are not known-good, the long block version of the same tiers includes the Essential Cylinder Head Service.
What else do I need for the install? The short block installation kit for your model year — gaskets, hardware, and break-in oil. Reusing old gaskets on a new bottom end is false economy.
What warranty do the tiers carry? All three carry the same 1-year / 12,000-mile warranty. Break-in and the first oil analysis are mandatory conditions.
Every tier starts from the same foundation decision. See why Crawford builds on brand-new OEM cases instead of machining used blocks.