EJ257 Long Block Tiers Compared: CSS 540 vs CCR 660 vs CRS 720+
Share
One listing. Three tiers. The difference is not trim — it is how much power the internals are built to hold, and what it costs to hold it. This is the decision post for the Crawford EJ255/EJ257 long block: which tier fits which build, in plain terms.
The general buyer's guide already covers what a long block is and what installation takes. This post covers the one question that guide leaves open: CSS, CCR, or CRS?
What every tier shares
All three tiers are the same program with different internals:
- Built to order in our shop from a brand-new OEM short block — no core required, no core charge, no used case put back in service.
- Fits 2004–2021 WRX and STI. If your car is a WRX, its turbo EJ is the EJ255. If it is an STI, it is the EJ257. Same build, same prices — pick your engine and your tier.
- Crawford Essential Cylinder Head Service included. Your heads are inspected and prepped, then assembled onto the new block. The top end that goes on is known-good, not a guess.
- Upgraded bearings in every tier.
- Ships free (continental US). Built long blocks ship free; that is the policy, not a promotion.
- 1-year / 12,000-mile warranty, with 24-month ($1,299) and 36-month ($1,999) extended coverage available on long blocks.
- Lead time is 2–4 weeks — built to order, final sale.
- Break-in is not optional: oil changes at 500 and 1,500 miles, 2,000–4,500 RPM varied, no sustained cruising or full-throttle pulls, no more than 80% of target boost until break-in is complete, and the first oil analysis is mandatory. It is a warranty condition.
CSS 540 — the street tier — $6,999 MSRP
Rated to 450 whp (540 bhp). The internals step is the pistons: CrawfordSPEC CSS forged pistons, made by JE Pistons, on the new OEM block with upgraded bearings.
This is the tier for a street car done right: stock-location turbo upgrades, a daily driver that gets driven hard, a replacement for a tired or failed stock motor that will not stay stock. Past 350 whp the factory cast pistons are the weak point — the ringlands go first. The CSS removes that ceiling without paying for parts the build will never use.
CCR 660 — the rod tier — $7,899.99 MSRP
Rated to 550 whp (660 bhp). Two steps up from the CSS: CrawfordSPEC CCR JE forged pistons, and CrawfordSPEC X-Beam billet rods developed with Pauter Rods — longer than stock for a better rod ratio, billet 4340 chrome-moly.
The rods are the story at this level. Between 450 and 550 whp, cylinder pressure stops being a piston problem and becomes a rod problem. If the build plan includes a rotated turbo, E85, or track days at real power, this is the tier. The $900 step over the CSS is cheaper than opening the motor twice.
CRS 720+ — the top tier — $8,499 MSRP
Rated to 600+ whp (720+ bhp) — the top of the Crawford line. CrawfordSPEC CRS FSR billet forged pistons: 100% CNC-machined from 2618-T6 bar stock, Forged Side Relief design, up to 32 grams lighter than a traditional forging, with 9310 steel wrist pins. CrawfordSPEC forged rods underneath.
This tier exists for drag and serious track builds where the motor lives at the top of the tach and the top of the boost gauge. The lighter piston is not a spec-sheet flourish — less reciprocating weight is less load on everything at high RPM. If the car will never see 600 whp, the CCR is the honest buy. If it will, nothing below this tier is.
How to choose
Build for a number, not a feeling. Pick the honest power target — the turbo, fuel system, and tune you will actually run — and buy the tier rated above it, not at it.
- 450 whp or less, street-first car: CSS 540.
- 450–550 whp, rotated turbo, E85, or track use: CCR 660.
- 600+ whp, drag or dedicated track: CRS 720+.
Two warnings that apply to all three. First, the tier does not save a bad tune or a contaminated oil system — after a failure, everything that shared oil with the old motor gets cleaned or replaced, and the tune has to be a professional custom tune for your exact combination. For e-tuning, Crawford recommends Delicious Tuning. Second, if your heads are known-good and you only need the bottom end, the same tiers exist as built short blocks — the long block earns its price when the heads are tired, damaged, or unproven.
Whichever tier you pick, protect it the same way: an Air Oil Separator to keep oil out of the intake charge, the break-in followed to the letter, and the oil analysis read properly when it comes back.
Questions on which tier fits your build: (855) 677-8243.
FAQ
Is the price the same for EJ255 and EJ257? Yes. Each tier is one price for both engines — CSS 540 $6,999, CCR 660 $7,899.99, CRS 720+ $8,499. WRX cars order the 255 variant, STI cars the 257.
Do I need to send a core? No. Every tier starts from a brand-new OEM short block. No core charge, no core return. You do send your heads — the Essential Cylinder Head Service (inspection and prep) is included in the price.
Can I order a tier now and grow into it? Yes, and it is the smart way to buy. Forged internals installed once cost far less than pulling the engine to upgrade later. Buy the tier above your current target if a bigger turbo is in the plan.
What does shipping cost? Nothing in the continental US. Crawford-built long blocks ship free.
What warranty do the tiers carry? All three carry the same 1-year / 12,000-mile warranty, with 24- and 36-month extended plans available. Break-in and the first oil analysis are mandatory conditions.
Same tiers, bottom end only
If your heads are known-good and only the bottom end needs replacing, the same three tiers exist as short blocks — CSS 540 $4,999, CCR 660 $5,599, CRS 720+ $5,999. See EJ257 short block tiers compared.