Crawford built EJ257 short block case showing the cylinder decks the head studs clamp against

Head Studs and Clamping Force on the EJ: Torque, Stretch, and Head Gasket Sealing

Every power stroke tries to lift the cylinder head off the block. That is not a figure of speech. Combustion pressure pushes up on the head with the full area of the bore behind it, and the only thing holding the head down — and the head gasket sealed — is the clamping force of the fasteners around each cylinder. On a stock EJ at stock boost, the factory hardware has margin. On a built EJ making real boost, that margin is the build. This is how clamping force actually works, and why Crawford builds EJ motors on studs, not bolts.

Torque is not clamping force

A torque wrench measures resistance to turning. What the gasket feels is clamping force — the fastener stretched like a spring, pulling the head and the deck together. The two are related, but they are not the same number. Most of the torque applied to a fastener is consumed by friction: under the nut or bolt head, and in the threads. Change the friction — dry threads versus oiled threads, a rough washer face versus a smooth one — and the same wrench reading produces a different stretch, and a different clamp load.

That is why assembly procedure specifies lubrication and sequence, not just a number. The number only means something with the friction condition it was written for. Guess at either and the clamp load across the gasket is uneven, even if every fastener clicked the wrench at the same setting.

Stretch is the measurement that matters

A fastener clamps because it stretches elastically — a small, controlled elongation that loads it like a spring. Within the elastic range, more stretch is more clamp, and the fastener returns to its original length when it is removed. Past the yield point, the fastener stretches permanently and the clamp load stops rising predictably.

Factory head bolts on a Subaru are torque-to-yield hardware: they are tightened into that permanent-stretch zone on purpose, which is why they are single-use. Reuse a yielded bolt and you are clamping with a spring that has already been sprung. A stud works differently. The stud threads into the case and stays there; the nut does the clamping. Friction is confined to the nut, the stud itself only stretches, and the result is a more consistent clamp load for a given torque — and hardware that can be used again.

Why Crawford builds on 11mm ARP head studs

Crawford's EJ practice is settled: a new short block goes together with 11mm ARP head studs. The studs were originally designed by Quirt Crawford, they are reusable, and they are the hardware specified in Crawford's own engine guide, Everything You Need to Know About Your Subaru Engine.

You do not have to buy a built motor to get them. Every EJ25 Short Block Installation Kit ($799.95; the installation kits run $699.95–$799.99 by application) includes 12 of the 11mm ARP head studs, OEM head gaskets, the intake and exhaust manifold gaskets, oil pump and seals, NGK one-step-colder iridium plugs, a K&N oil filter, and Motul break-in oil. The studs are in the kit because the clamp is part of the motor, not an accessory.

Sequence: even clamp, in stages

Clamping force only seals if it is even. Tighten one side of a head fully before the other and the gasket is pinched hard at one end and barely loaded at the other — the lightly loaded end is where the seal lets go under pressure. The factory sequence works from the center outward in stages for exactly this reason: bring the whole gasket up to load gradually and evenly, so the head comes down flat and stays flat.

The gasket itself is the other half of the seal. A multi-layer steel gasket needs clamp load and a correctly finished surface to do its work — the two decisions are made together, which is the subject of the head gasket kit guide. And like bearing clearances and ring gaps, the fastener and gasket spec for a Crawford motor is recorded on its build sheet — see what a build sheet records.

What failure looks like

When clamping force loses to cylinder pressure, the head lifts microscopically on the power stroke and sets back down. The gasket, worked back and forth, frets and fails: combustion gas into the cooling system, coolant into the cylinder, or both. It rarely starts as a dramatic blowout. It starts as pressure in the cooling system, a coolant level that drops for no visible reason, and a misfire on a cold start. By the time it is obvious, the gasket is done.

The risk scales with cylinder pressure, which is why this matters more as power rises. The built EJ257 short blocks — CSS 540 at $4,999 MSRP, CCR 660 at $5,599 MSRP, CRS 720+ at $5,999 MSRP — all run on brand-new OEM cases with forged internals, and all of them depend on the same clamping arithmetic. Boost is pressure. Pressure is what the studs are holding back.

Questions on a build: (855) 677-8243.

Frequently asked questions

Are head studs better than head bolts on an EJ?
For a built motor, yes. A stud confines friction to the nut, so torque converts to stretch — and therefore clamping force — more consistently. Studs are also reusable; factory torque-to-yield bolts are single-use.

What head studs does Crawford use?
11mm ARP head studs, originally designed by Quirt Crawford. They are specified for Crawford EJ builds and included in the Crawford short block installation kits.

Why does torque alone not guarantee the right clamp load?
Because most of the applied torque is consumed by friction, and friction varies with lubrication and surface condition. Same torque, different friction, different stretch. That is why the specified lubricant and sequence are part of the spec.

Can I reuse my factory head bolts?
No. Factory head bolts are torque-to-yield — they are permanently stretched at installation. New hardware on every build.

What are the first signs of a head gasket losing its seal?
Cooling system pressure, unexplained coolant loss, and cold-start misfires. Those are clamping or gasket problems announcing themselves early — have them checked before the gasket fails outright.

Back to blog