Subaru Head Gasket Kit Guide: OEM vs MLS for EJ Builds
Share
Choosing a head gasket kit for an EJ255 or EJ257 is not a parts-counter decision. The right seal depends on the engine's intended use, the condition of the deck and heads, gasket thickness, and the fasteners holding the clamp load. A stock daily-driver repair and a high-boost build do not take the same kit.
One more thing first: the gasket is usually the messenger, not the cause. Gaskets fail because a surface moved, a fastener lost clamp, or the engine overheated. Replace it without finding the reason and you will do the job twice.
What a complete kit includes
A gasket-only package may hold just the two head gaskets. That works when the engine is already apart and every other seal is on hand. For most top-end repairs and rebuilds, a complete kit is the safer spec:
- Head gaskets — seal combustion pressure and separate the coolant and oil passages between block and heads.
- Intake and exhaust manifold gaskets — reusing compressed or damaged ones invites air, exhaust, and boost leaks.
- Valve cover gaskets — contain oil around the valvetrain.
- Spark plug tube seals — keep oil out of the plug wells. A new head gasket does nothing for that leak path.
- Oil-passage seals and O-rings — a failed passage seal leaks externally or costs oil pressure.
- Fasteners, on some kits — new head bolts or upgraded studs. They deliver the clamp load the gasket seals with; a stretched or wrong fastener undermines good parts.
Compare the kit contents against what came off the engine, and confirm engine code, model-year range, gasket thickness, and fastener type before ordering. A kit assembled for a routine top-end repair is not automatically complete for a rebuilt short block — review the EJ25 short block installation kit for the lower end, and the Subaru cylinder head rebuild guide for head inspection and machine work.
OEM vs MLS: which fits the job
Neither gasket corrects a warped head, a damaged deck, or a bad installation. Start there.
| OEM-style | MLS | |
|---|---|---|
| Typical use | Stock or near-stock EJ255/EJ257, daily-driven in the factory operating range | Rebuilt and performance engines, built blocks, higher cylinder pressure |
| Surface demand | Clean, flat, inspected surfaces | Less forgiving — flatness and surface finish must meet the gasket maker's spec |
| Fasteners | New bolts to the service procedure | Often paired with upgraded studs, treated as one clamping system |
An OEM-style gasket is the right call for a stock engine with measured, healthy surfaces. An MLS gasket earns its place when boost and cylinder pressure climb — provided the surfaces are finished for it and the clamping strategy matches. MLS is not automatically the upgrade. Fitted over poor machine work, it seals worse than the gasket it replaced.
Thickness matters as much as material. If the heads were resurfaced or the deck machined, the gasket thickness has to support the planned deck clearance and compression ratio. Choose from measured geometry, not from the most aggressive option on the shelf.
Why EJ head gaskets fail
Every heat cycle works the joint. Aluminum heads, the block, the fasteners, and the gasket all expand at different rates. A marginal seal survives stock use and gives up under a performance build's pressure and cycling.
The common root causes:
- Warped or damaged surfaces — overheating history, fire-ring damage, corrosion at coolant passages.
- Lost clamp load — stretched bolts, wrong sequence, debris or fluid in a blind bolt hole skewing the torque reading.
- Detonation and overheating — the failure that killed the first gasket will kill the second one if the tune and cooling system are not addressed.
Symptoms — overheating, bubbles in the coolant reservoir, unexplained coolant loss, oil and coolant mixing — overlap with cooling-system and head problems. Diagnose before you order: cooling-system pressure test, compression, leakdown. Confirm the failure mode, inspect the heads and block, then pick parts.
Spec'ing a kit for a built block
- Record the exact combination. Engine family, model-year range, bore, head application, and block type — stock case, sleeved, or closed-deck conversion.
- Measure flatness. Block deck and both heads, after cleaning. Check for warpage, fire-ring damage, and corrosion. Confirm the surface finish the gasket requires with your machine shop.
- Choose material and thickness from the measurements. Thickness sets deck clearance, piston-to-head clearance, and compression. It is a calculated choice, not a preference.
- Decide the fastener strategy. Replace bolts that are out of spec or not reusable. A high-boost build usually takes upgraded studs — confirm thread engagement, washers, lubricant, and sequence.
- Confirm every supporting seal. Manifold gaskets, valve cover gaskets, tube seals, passage seals. Nothing missing when the heads go on.
For the parts around the gasket decision, see the EJ25 short block installation kit and the cylinder head rebuild guide. Document the spec — fitment, surfaces, thickness, clamping — and the next person to service the engine knows what is in it.
Installation details that protect the seal
- Prep both surfaces. Clean, flat, free of old gasket material, corrosion, and debris. No aggressive tools gouging the deck; keep abrasives out of the oil and coolant passages.
- Clean the bolt holes. Fluid or debris trapped in a blind hole produces a false torque reading and uneven clamp.
- Follow the exact procedure. Specified sequence, specified stages, torque-angle steps where the procedure calls for them, calibrated wrench. Bolts and studs are not interchangeable because they fit the same holes.
- Clean the cooling system. A failed gasket leaves oil and combustion byproducts in it. Flush it, inspect the radiator and hoses, refill with the correct coolant. Contamination left behind undermines correct machine work. The head gasket replacement guide covers teardown and reassembly in more depth.
Frequently asked questions
Should I choose OEM or MLS? Stock EJ255 or EJ257, daily-driven in its factory range, surfaces measured and healthy: OEM-style. Rebuilt or performance engine: usually MLS, with the surfaces finished for it and the fasteners to match. The engine's condition decides, not the gasket's reputation.
What is the best kit for a built engine? The one spec'd from the build: MLS matched to upgraded studs where the boost plan calls for them, thickness from measured deck height and head work, every supporting seal included.
How do I know my Subaru needs a head gasket? Overheating, bubbles in the reservoir, coolant loss, white exhaust smoke, oil and coolant mixing. Each has other possible causes. Test first — pressure, compression, leakdown — before the engine comes apart.
Can head gaskets be replaced with the engine in the car? Sometimes, physically. Pulling the engine gives the access to clean, inspect, and measure the deck and heads properly. A new gasket will not seal warped surfaces no matter how carefully it is fitted.
For help spec'ing a kit, use the Crawford Performance contact page with the engine code, block configuration, head work, intended use, and fastener plan — or call (855) 677-8243.
Related reading: the gasket only seals if the clamping force behind it is right — see head studs and clamping force on the EJ for how torque, stretch, and sequence decide the seal.