FA20 Engine Guide: Specs, Failures, and Upgrades
Share
The FA20 comes in two versions: the naturally aspirated FA20D powers the BRZ, FR-S, and 86; the turbocharged FA20DIT powers the WRX and the Forester XT. They share an architecture and almost nothing else that matters. Identify which one you have before you order parts or plan a build.
What the FA20 Is
The FA20 is a 1,998 cc (2.0L) horizontally opposed four-cylinder — two cylinders per side, keeping it compact with a low center of gravity. It uses dual overhead camshafts, 16 valves, direct injection, and dual AVCS variable valve timing on both cams. Bore and stroke are both 86.0 mm — a square engine.
Both run Subaru's specified 0W-20 oil, and AVCS depends on clean oil at the right pressure, so oil quality and intervals matter. The FA20 uses a timing chain, not a belt, so there is no belt replacement interval.
FA20D vs. FA20DIT: Specs and Differences
| Specification | FA20D | FA20DIT / FA20F |
|---|---|---|
| Induction | Naturally aspirated | Turbocharged, twin-scroll turbo |
| Compression ratio | 12.5:1 | 10.6:1 |
| Output | About 200 hp and 151 lb-ft | About 268 hp and 258 lb-ft |
| Primary applications | Subaru BRZ, Scion FR-S, Toyota 86 | 2015–2021 WRX, 2014–2018 Forester XT, JDM Legacy GT |
The BRZ version uses D-4S, combining direct and port injection. NA and turbo parts do not interchange, and neither do their calibrations.
Common Failure Points
Its failures are predictable — most trace back to heat, detonation, oil quality, or how the engine is loaded.
Ringlands and detonation
Ringland failure is the family's known weakness under boost, especially on a FA20DIT running an aggressive calibration. Detonation creates sharp pressure spikes that crack piston ringlands, and high boost raises the cost of a marginal tune or bad fuel. Use a calibration written for your exact fuel, hardware, and boost level, address knock promptly, and do not add boost before the supporting systems are ready. Crawford's ringland failure guide covers this failure in depth.
Rod knock from lugging
Rod knock is the other known FA20DIT failure. It comes from heavy load at very low RPM: lugging raises cylinder pressure while engine speed is too low, and the rods and bearings take the stress. On the stock engine, the connecting rods are the weak point past roughly 350 lb-ft of torque. Downshift before a grade, a pass, or hard acceleration instead of asking for boost in a tall gear.
Carbon buildup
The FA20DIT is direct injection only, so fuel never washes the intake valves and carbon builds up on them over time — airflow, idle quality, and power suffer. Watch for drivability changes; plan on intake-valve inspection and cleaning as mileage climbs.
Valve springs, early engines
Early 2012–2013 engines had a documented valve-spring issue, addressed by a Subaru recall in 2018. On an early engine, confirm that campaign was completed.
Timing chain wear
Pre-2016 engines are more prone to timing-chain wear, particularly with extended oil intervals and high thermal stress; later revisions improved the guides and tensioners. On any FA20, timely oil service is the prevention — investigate chain noise or timing faults early.
When damage has already progressed, the fix starts with a documented diagnosis, not a pile of replacement parts thrown at an undiagnosed engine.
The Upgrade Path
Build in order — supporting systems come before the next level, not after something breaks.
Start with a healthy engine
Confirm compression and leak-down, inspect oiling, and monitor oil pressure, air-fuel ratio, knock, and temperature. Fix maintenance items first — power added to a sick engine just shortens its life.
Oil control belongs here. Crawford developed the original closed-loop Subaru air/oil separator: it pulls oil out of the crankcase vapor and drains it back to the crankcase instead of the intake. Crawford's AOS is aluminum and made in the USA. It carries no CARB EO, so check the EO status for your application. See the air/oil separator collection.
Bolt-ons, and the tune that has to follow
Intake, downpipe, and exhaust changes improve airflow on the DIT — and change what the engine needs from its calibration. Any change to airflow or fueling requires a professional tune matched to the fuel, the hardware, and the boost level. Crawford does not sell tuning; that step belongs to a tuner, and it is not optional.
For the naturally aspirated FA20D, the honest bolt-on is Billet Power Blocks: about 15 hp, more power down low, stock intake.
Turbo and supporting systems
A larger turbo moves the FA20DIT past the stock turbo's range and raises heat, boost, and load everywhere. Fuel delivery, charge-air cooling, and drivetrain capacity have to be sized to the target at the same time. Crawford's built FA20 engine guide covers the planning.
The built short block
When the target passes what the stock rods will hold, the factory short block is the limit — no bolt-on changes that. The answer is a built short block with forged internals specified for the goal.
Crawford's FA20 DIT short block is rated at 660 hp, with CrawfordSPEC forged pistons made by JE Pistons. Crawford builds on brand-new OEM blocks only — no core is required or needed, no core charge, nothing to ship back. Short blocks and long blocks are both available in the Subaru engines collection, and Crawford-built long blocks ship free.
Break-in is a warranty condition: oil changes at 500 and 1,500 miles; keep engine speed between 2,000 and 4,500 RPM, varied, with no sustained cruising or full-throttle pulls; do not exceed 80% of target boost until break-in is complete; the first oil analysis is mandatory. Built engines carry a 1-year / 12,000-mile warranty.
Why Crawford
Crawford is the only aftermarket manufacturer ever factory-backed by Subaru of America, and Crawford built the engines for the Ken Block Gymkhana cars.
Questions about your FA20 build: call (855) 677-8243 or reach us through customer support.
Frequently Asked Questions
Is the FA20 a reliable engine?
It can be, when maintained and calibrated for its hardware. The FA20D is dependable at factory output; a modified turbo engine has less margin for tuning, heat, and oiling errors.
How much power can a stock FA20 handle?
Torque breaks it, not a headline horsepower number. The stock connecting rods are the weak point past roughly 350 lb-ft of torque. Fuel, tune, boost, and temperature control move that line around but do not remove it. Past it, the short block is the conversation.
Why upgrade to a built FA20 short block?
When your power target, boost level, or track use has passed the factory assembly's margin. Forged internals address the known weak points and add overhead — but fueling, calibration, cooling, and oil control still have to match.
Modding the DIT? Read the FA20 DIT mods and tuning guide.
Gasket let go? Read the FA20 head gasket guide.