Subaru Engine Builds: A Start-to-Finish Guide
Share
A built engine does not create power. It creates a foundation that holds power without failing. Past roughly 400 horsepower, forged internals stop being an upgrade and become the requirement. This guide walks the whole process: choosing the platform, knowing when stock is no longer enough, what goes inside a built motor, what it costs, the supporting systems it needs, and how to keep it alive afterward.
FA20 vs. FA24: Which Engine Should You Build?
The FA20. A 2.0-liter boxer found in the 2015+ WRX and the 2013+ BRZ. Stock, with a good tune and basic bolt-ons, it handles around 350 wheel horsepower reliably. Pushing toward 400 whp on stock internals is possible and risky — the connecting rods are the first component to fail under the added cylinder pressure. Built with forged internals, the FA20 handles over 600 hp. Crawford's FA20 DIT short block is rated at 660 hp. The platform is well understood, and its weak points are known. The forged FA20 long block is the built version of this path.
The FA24. A 2.4-liter boxer in the latest generation of Subaru vehicles, including the current WRX. The extra displacement brings more low-end torque. That is the identification. Crawford's built-motor program covers the EJ and FA20 generations, and the build guidance in this guide applies to those engines.
Which one for your goals. A fun street car at 450–500 hp is built-FA20 territory: a full set of forged internals on a well-understood platform. Decide by how you drive — high RPM on track, or torque down low every day — and by a stated power goal, not by whichever engine is newer.
When Do You Need a Built Subaru Engine?
Factory weak points. A stock engine is engineered to balance performance, reliability, and cost at stock power. Add significant power and the weak points surface. On the FA20, the safe limit on stock internals is around 350 whp; toward 400 whp the connecting rods become the risk, and hard use raises oil consumption, a sign of the stress. The same logic applies to the EJ257: reliable to about 350 whp stock, with the cast pistons' ringlands as the failure point past it — covered in EJ25 short block reliability.
The myth. There is no massive power gain hiding in a stock engine behind a few bolt-ons and an aggressive tune. The factory pistons, rods, and bearings were designed for stock power levels. Push a stock block too far and failure is a matter of when, not if. A built engine replaces those parts with forged components designed for the heat and pressure.
The threshold. If your goal sits inside 350–400 horsepower, a built motor may not be necessary. At 500, 600, or more, it is non-negotiable. The built engine's job is to make that power level survivable, every pull, for years.
What's Inside a Forged Subaru Engine?
Forged internals: pistons and rods. Factory pistons and rods are cast — molten metal poured into a mold. Casting is efficient for mass production and leaves the parts more brittle under high stress. Forging shapes metal under extreme pressure, producing a denser, stronger part. Forged pistons and rods are the single most important step in preparing an engine for power, because the factory connecting rods are a known failure point in Subaru engines. Crawford's pistons are CrawfordSPEC forged pistons made by JE Pistons.
Upgraded hardware: studs and bearings. Higher boost raises cylinder pressure enough to stretch factory head bolts and let a head lift slightly off the block, breaking the head gasket seal. High-strength head studs provide the clamping force that keeps the heads planted. Performance bearings support the crankshaft between the block and the rods, made from materials that withstand higher loads and temperatures than stock.
Block and cylinder head work. Many Subaru boxer engines, the FA20 included, use an open-deck design with gaps around the tops of the cylinder walls for coolant flow. That is fine at stock power; under high boost the unsupported walls can flex. Crawford's answer is not a conversion process — it is a built block rated for your goal, starting from a brand-new OEM case. Heads are addressed for airflow: an engine makes power by moving air, and port work smooths and reshapes the intake and exhaust ports so more air moves with less turbulence. Crawford's head packages are Rebel, Bandit, and Outlaw — Rebel covers cleaning, damage inspection, precision valve work, and resurfacing; Bandit adds professional port and polish; Outlaw is hand-finished, race-spec porting for engines pushing over 700 horsepower. Street Spec heads carry a 3-angle valve job and support builds up to 500 whp, and the machine shop services include a 5-angle valve job.
Cooling and oiling. More power makes more heat. A built engine typically needs an upgraded aluminum radiator, a high-performance thermostat, and often an external oil cooler to keep coolant and oil temperatures stable. On the oiling side, the air-oil separator is non-negotiable — covered in its own section below.
Short Block vs. Long Block: What's the Difference?
Short block. The bottom half of the engine: the block with the crankshaft, connecting rods, and pistons installed. No cylinder heads, camshafts, or valvetrain. It is the foundation, and the route for owners whose existing heads are in good shape and who want to handle the top-end assembly themselves. Crawford sells a Short Block Installation Kit for that installation — an install kit, not a rebuild kit. One distinction matters: a home rebuild machines your used block. Crawford's path is different — every Crawford short block starts from a brand-new OEM block, so there is no core required, no core charge, and no core return.
Long block. Everything in the short block plus cylinder heads, camshafts, and valvetrain — a fully assembled engine from oil pan to valve covers. It removes the complex work of assembling heads and setting valve timing, and it is the preferred route for builds far past stock power, because every internal component is ready for the stress. The comparison is laid out in long block vs. short block, and the FA20 version is in FA20 long block.
Which one for your build. Short block if your factory heads are in good shape and you are comfortable with top-end assembly — and follow the factory service manual for torque specs and sequences, because this guide does not substitute for it. Long block if the goal is high power with the fewest installation variables. Crawford builds both, including a build-to-order lane — the built-to-order long blocks page explains it. Crawford-built long blocks ship free.
How Much Does a Subaru Engine Build Cost?
Core engine costs. A short block typically runs between $5,000 and $6,000. A complete long block ranges from $9,000 to over $19,000 depending on components and builder. Remember what the money buys: the block itself adds no horsepower. It raises the ceiling — a stock FA20 safely handles around 350–400 horsepower; a properly built engine reliably manages over 600.
The costs around the engine. Budget past the block. There is no core charge on a Crawford engine and nothing to ship back, but the new engine still ships to you. Break-in oil is part of the first miles. A professional tune is not optional and belongs in the budget as its own line. So do the supporting systems below — cooling, fuel, and oil management. Crawford-made parts carry one price, labeled MSRP.
A realistic budget. Start with the block, then price the complete system: turbo, fuel, cooling, oiling, tune, installation labor, and the drivetrain and brake items a faster car needs. A build planned as a complete, balanced system from the start is how costly surprises get avoided.
Essential Supporting Mods for Your Built Engine
Turbocharger. A built engine can hold more boost, and reaching the target usually takes a larger turbo — at 600 horsepower or more, the stock turbo will not keep up. Match the turbo's size and flow to the engine's displacement and the powerband you want: too large brings lag, too small chokes the engine at high RPM. A larger turbo also requires a larger intercooler, an upgraded radiator, and a clutch that can hold the extra torque.
Fuel system. More air and more boost demand more fuel, and the stock fuel system was designed for factory power. Running lean invites detonation and engine damage. The upgrade is a higher-flow fuel pump, larger injectors, and sometimes upgraded lines and rails. On E85, fuel demand increases by about 30%, and every component must be compatible with the fuel.
Airflow: intake, intercooler, exhaust. An engine is an air pump. A restrictive stock intake starves a larger turbo; a performance exhaust reduces backpressure, lets the turbo spool faster, and improves efficiency. The intercooler cools the charge air after the turbo, and denser air makes more power. The WRX upgrades collection is where the Crawford parts for this sit.
Drivetrain and brakes. Double or triple the factory horsepower strains everything behind the engine. The clutch is usually the first component to fail; at higher levels the transmission, driveshaft, and axles come into the plan. Brakes are part of the same equation — pads, rotors, and fluid that can manage the speeds the car is now capable of.
Why an Air-Oil Separator Is Non-Negotiable
The flat-four design lets oil vapor from the crankcase recirculate into the intake through the PCV system, especially at high RPM and high load. That vapor lowers the fuel's effective octane, which can lead to detonation, and coats the intake valves with carbon buildup. An air-oil separator captures the vapor, returns the oil to the crankcase, and sends only clean air into the engine. Crawford developed the original closed-loop Subaru AOS. It is aluminum, made in the USA with USA components, and it is a reliability part first — essential insurance on a built motor, not an accessory. Crawford's AOS carries no CARB EO, so check the EO status for your application. The FA20 application is in the AOS collection.
Why Tuning Is More Important Than Parts
The factory ECU is programmed for a stock engine. Add airflow or fuel and the stock calibration cannot compensate — the result is knock, lean air-fuel ratios, or excessive cylinder pressure, any of which can destroy a built engine. A professional tune calibrates fuel delivery, ignition timing, and boost pressure into a custom map matched to your hardware, your fuel, and your goal. Its primary job is reliability: it establishes a safe operating window for the engine.
Be plain about one thing: Crawford does not sell tuning. Engines are designed to work with a professional tune, and that tune is done by a platform specialist. It is not an optional final step, and it is not deferrable. This applies to the FA20 in full: its stock computer cannot manage a larger turbo or high-flow injectors, and the calibration has to be written for the hardware installed.
After the tune, monitor the engine. Oil pressure, coolant temperature, and air-fuel ratio are the readings that matter — low oil pressure points to a lubrication problem, high coolant temperature to a cooling problem, and an off AFR to a fuel delivery problem. Gauges are one of the smartest supporting additions on a built car. Catching a small issue early is how a built engine stays built.
How to Choose a Subaru Engine Builder
Platform experience. Boxer engines have their own characteristics, and a shop that primarily builds V8s does not have the specialized knowledge. Look for a builder whose work is Subaru engines — FA20 and EJ — with a transparent process and straight answers about assembly methods and component choices. A builder who cannot or will not answer detailed questions is a reason to walk away. The FA20 builder landscape is covered in FA20 long block builders, and what separates Crawford is in the Crawford difference.
The warranty. A warranty is the builder's vote of confidence in his own work. Crawford's built engines carry a 1-year / 12,000-mile warranty. Break-in and the first oil analysis are mandatory conditions of it. Ask any builder for the warranty terms up front, and understand the conditions — many require professional installation and tuning, which is reasonable, because a bad installation or a bad tune can damage the best-built engine.
Red flags. A price that seems too good to be true. A shop that downplays supporting modifications or the tune — a built short block alone does not make 500 horsepower; the fuel, air, and cooling systems have to support it. And hidden costs: ask for the complete out-the-door price, including shipping and taxes, before you commit.
How to Maintain Your Built Subaru Engine
Break-in. The first miles seat the piston rings against the cylinder walls, which creates the seal for compression and oil control. Crawford's break-in spec is specific. Change the oil at 500 and 1,500 miles. Keep engine speed between 2,000 and 4,500 RPM, varied — no sustained cruising, and no full-throttle pulls. Do not exceed 80% of target boost until break-in is complete. The first oil analysis is mandatory; it is a warranty condition. Patience in this phase is what buys a long engine life.
Long-term schedule. Change oil and filter every 3,000 to 4,000 miles with a high-quality synthetic. Check fluid levels regularly and inspect for leaks. On direct-injection engines like the FA20, professional carbon cleaning is a necessary service every 40,000 to 60,000 miles. Keep watching air-fuel ratios, boost, and temperatures — the monitoring habit from the tuning section does not end.
Match the plan to the car. A 500+ horsepower track build and a 400-horsepower daily driver have different maintenance needs. A track engine may need thicker oil and more frequent inspections, which is impractical on a street car; a high-strung build used for short stop-and-go trips rarely reaches operating temperature and wears for it. Be realistic about how the car gets used before the build starts, and maintain it for that use.
Explore Crawford Performance Engine Builds
Crawford builds engines stronger than factory by replacing the weak stock components with forged parts — CrawfordSPEC JE forged pistons, forged rods, and hardware chosen for the rating. Every build starts from a brand-new OEM block. No core is required or needed. The current EJ line is rated by name:
- CrawfordSPEC CSS 540 — 450 whp / 540 bhp
- Club Racer CCR 660 — 550 whp / 660 bhp
- Racer Spec CRS 720+ — 600+ whp / 720+ bhp
The legacy stage-named EJ blocks — S2 (450 whp), S3L-X (550 whp), and S3L-X FSR (600+ whp) — keep their names and ratings as legacy blocks. The FA20 DIT short block is rated at 660 hp. Short blocks and long blocks are both available, built and build-to-order, and Crawford-built long blocks ship free. Crawford is the only aftermarket manufacturer ever factory-backed by Subaru of America. Built engines carry the 1-year / 12,000-mile warranty, with break-in and the first oil analysis mandatory. Questions: (855) 677-8243.
Frequently Asked Questions
What is a realistic total budget? The block is the starting point: a forged short block runs $5,000 to $6,000, and a complete long block ranges from $9,000 to over $19,000. Add the supporting systems — larger turbo, fuel system, cooling — plus a professional tune and installation labor, and set aside for a stronger clutch and better brakes. A successful build is a complete, balanced system, planned that way from the beginning.
Is a built engine less reliable than a stock one? A stock engine is reliable inside its intended limits. Push it past 400 horsepower and you are outside those limits, and failure becomes a risk. A built engine replaces the weak points — cast connecting rods first — with forged components, and paired with a professional tune and proper maintenance it is the durable foundation for high power.
Why is an AOS so important on a built engine? The boxer design pushes oil vapor into the intake. That vapor lowers the fuel's octane and can cause knock — extremely dangerous on a high-horsepower build — and it bakes carbon onto the valves. An AOS returns the oil to the engine and sends only clean air into the combustion chamber.
What is the very first step? Define the goal before buying a single part. Two questions: what is the target horsepower, and how will the car actually be used? A 600-horsepower track car and a 450-horsepower daily driver are different builds in every decision that follows — builder, budget, and supporting parts.
Compression decides the piston spec: the Subaru compression ratio guide.
Related reading: for the money side of the same decisions, see the STI engine build cost guide.
Planning the whole build rather than one part at a time? The Subaru performance engine upgrade guide lays out the order that matters.