BRZ track day prep checklist
Share
A quick BRZ becomes a liability when heat, worn brakes, or loose hardware end the session early. Reliable laps start in the garage. Track day prep is not about power — it is about making the car repeatable, predictable, and safe, in that order. More power increases load. It fixes nothing.
Do this a week before the event, not the night before. That timing leaves room to fix what you find.
One week out: the inspection
- Leaks first. Look for oil, coolant, and brake fluid leaks, then verify every fluid level. A seep at street pace is a failure at track pace.
- Engine oil. Fresh oil, correct level — and on this engine, read the oil starvation guide before you go. Sustained high-G cornering is the FA20's known weakness; level discipline and, for regulars, the Killer B pickup ($153.00) are part of prep, not upgrades.
- Brake fluid. Replace old or unknown fluid with fresh high-temperature DOT 4. Fluid vaporizes under severe heat, and a long pedal at the end of a straight is how sessions — and cars — end.
- Pads and rotors. Measure inner and outer pad thickness at all four corners. Replace pads that cannot cover every planned session. Inspect rotors for heat cracks, deep grooves, and a heavy outer lip.
- Tires. Check tread across the whole tire, including the inside shoulder — BRZ alignment hides wear there. Look for cords, cuts, bulges. Set a conservative cold pressure and record it.
- Wheels and hardware. Check for bearing play and wheel cracks. Torque lug nuts to the factory specification. Inspect the belt, battery hold-down, exhaust mounts, undertrays, and suspension hardware. Remove loose cabin items.
The oil-control item most BRZs are missing
Under sustained cornering and high RPM, crankcase pressure pushes oil vapor through the intake. Crawford's BRZ/FR-S/86 AOS V3 — $449.99 MSRP — separates that vapor in closed loop and returns the oil to the pan: no catch can to drain, no vapor coating the intake. It does not prevent oil starvation (that is level, pickup, and baffling — see the guide above), and it is not sold as if it does. It handles the other half of the FA20's oil management, which track use stresses hardest.
Between sessions
Track use accelerates wear; a shorter version of the inspection repeats all day.
- Recheck oil and coolant levels. Note any change — consumption that appears on track is information.
- Check hot tire pressures against your morning baseline; uneven growth points at alignment or loading.
- Feel the brake pedal. Any change in feel means look, not hope.
- Record pad wear, tire condition, oil temperature behavior, and anything new — noise, vibration, smell.
Stop immediately if temperatures climb or braking performance changes. A shortened day is a cheap day.
Adding power, in the right order
Add power only after the car completes sessions without fluid loss, brake fade, heat problems, or new noises. Treat the first event as data collection: the record shows which upgrade solves a real limit.
For the FA20, the honest first power step is airflow. Crawford's Billet Power Blocks for the BRZ/FR-S/GT86 — $329.99 MSRP — lengthen the intake runners for roughly 15 more horsepower and stronger low-end response on the stock intake, no tune required. When the goal outgrows bolt-ons, the foundation is a built FA20 short block rated to 660 horsepower ($5,999.99 MSRP) — built from a brand-new OEM block, no core.
The night before
- Fluids and tools packed: oil, brake fluid, torque wrench, pressure gauge, jack and stands.
- Numbers recorded: cold pressures, pad thickness, oil level.
- Loose items out of the cabin and trunk.
- A plan to stop. Decide now what ends your day — temperature, pedal feel, a new noise — so the decision is already made when pride argues otherwise.
Questions before an event: (855) 677-8243.
Frequently asked questions
What is the single most important BRZ track prep item? Brakes and fluids, tied. Fresh high-temp brake fluid and pads with material for the whole day prevent the failures that end events early — and the dangerous ones.
Do I need an oil cooler for my first track day? Watch the data first. Extended high-RPM sessions raise oil temperature; if your sessions are short and temperatures behave, drive and record. Recurring high readings make the case for more cooling capacity.
Should I overfill the oil for a track day? Many FA20 owners run 0.5 to 1 quart over on track as a buffer against starvation in long corners. It buys seconds, not immunity — the full picture is in the oil starvation guide linked above.
When is the car ready for power mods? After it finishes a full day with no fluid loss, no brake fade, no heat issues, and no new noises — and you have the notes to prove it.
Exhaust is the other track-day basic: the BRZ performance exhaust guide.
Related reading: brake fluid is a calendar item, not a condition item — the fluids guide covers RBF 600, RBF 660, and the flush schedule: Subaru fluids guide: the Motul line Crawford stocks.
The brakes section above has a full companion guide — compounds, rotors, and fluid, in order. See the Subaru brake upgrade guide.
Related reading: Whiteline and Cusco for Subaru WRX: Chassis, Suspension, and Grip