Your Guide to the Best BRZ Performance Exhaust
Share
The factory BRZ exhaust is a quiet compromise, built to balance cost, noise, and emissions for the average driver. A performance exhaust changes the car's sound first. It also frees up some power and cuts weight. This guide covers the system types, the materials, what they cost, and how to pick the one that fits your car and your plans.
What a Performance Exhaust Does
The stock system has tight bends and dense mufflers that create backpressure. The engine works harder to push exhaust gases out, and that costs power. A performance system uses larger-diameter piping and smooth mandrel bends that hold a consistent diameter through every curve. Exhaust gases exit with less resistance, throttle response sharpens, and the engine feels more willing to rev.
Know which BRZ you have before anything else. The first-generation car (2013–2020) runs a 2.0-liter flat-four. The second-generation car (2022–present) runs a 2.4-liter flat-four rated at 228 horsepower and 184 lb-ft of torque. The generations do not share exhaust fitment.
Sound is the biggest change. The stock BRZ is quiet. A performance system gives the boxer engine a deeper, sportier note that matches the car.
Weight is the quieter benefit. Factory systems are heavy, thick-walled steel. Performance systems are typically T304 stainless steel, which is lighter and resists corrosion. A full cat-back sheds the most weight, and every pound off sharpens acceleration, braking, and handling on a car this light.
The Crawford Option: Gymkhana 2
The Gymkhana 2 Exhaust is Crawford's exhaust for the 2013–2016 BRZ, Scion FR-S, and Toyota GT86. It is an axle-back system. It bolts directly onto the factory mid-pipe, and the stock catalytic converters stay in place.
It is a sound upgrade first: a deep, aggressive rumble in place of the quiet stock note. Axle-backs are worth one or two horsepower at most, and Crawford makes no dyno claim for it. What you get is the note, the look, and a straightforward installation.
The Gymkhana 2 is a first-generation part. Crawford does not list an exhaust for the 2022 and newer BRZ. If you own the second-generation car, confirm any system's stated fitment for your exact year before you buy — exhausts do not cross generations.
Cat-Back vs. Axle-Back vs. Header-Back
An axle-back replaces everything from the rear axle to the tips — the muffler and tips. It is the simplest, least expensive option, and installation often takes less than an hour. The gain is sound and appearance, not power.
A cat-back replaces everything from the catalytic converter back: mid-pipe, resonator, and muffler. Wider, smoother piping reduces backpressure across more of the system, so the power and sound changes are both larger than an axle-back's. A cat-back is also the right foundation if headers or other power parts come later, because the stock mid-pipe an axle-back keeps becomes the bottleneck as power rises.
Both systems leave the factory catalytic converters in place. The main restrictions in the stock system are the muffler and the mid-pipe, not the converters.
A header-back replaces everything from the exhaust manifold to the tips. It produces the largest exhaust gains, and it almost always requires a professional tune to run safely. Crawford does not sell tuning.
Sound follows the hardware. An axle-back is deeper and sportier than stock without being obnoxious. A cat-back is louder and deeper through the whole RPM range because the mid-pipe and resonator change too. For more on how the system types compare, see the cat-back exhaust guide and Crawford's rally exhaust article.
Noise rules vary by state and city. Check your local rules before you buy.
Sound: Tone Without Drone
Volume is easy. Tone is the engineering. Drone — the low-frequency hum at steady cruising speed — is what ruins a daily driver, and it is what good muffler and resonator design exists to cancel. Look for systems engineered with resonators or Helmholtz chambers that target those frequencies.
Valved systems go further. A valve routes exhaust through a muffled path when closed and a more direct path when open, so the car stays quiet on the commute and loud when you want it. Tips are the finishing piece: polished stainless for a clean look, black chrome for a stealthier one, carbon fiber for a race look.
What It Costs
Prices break down by system type and material:
- Entry level, $900–$1,200: high-quality axle-backs and basic cat-backs. Stainless construction, a clear sound upgrade, modest performance change.
- Mid-range, $1,200–$1,600: full cat-backs in T304 stainless, with the engineering time spent on tone and drone control.
- Premium, $1,600–$2,200: titanium construction for maximum weight savings, valved systems, and the most refined sound tuning.
Budget for installation on top of the parts. A professional install runs a few hundred dollars and buys a leak-free fit on a lift, with everything torqued to spec. Crawford-made parts carry one price, labeled MSRP.
Fitment: Generation and Platform
An exhaust is built to one car: its model years, engine, mounting points, and dimensions. The 2.0-liter first-generation car and the 2.4-liter second-generation car take different systems. Check the exact model years in the product description before you order.
The BRZ shares its platform with the Scion FR-S and Toyota GT86, and many parts interchange — the Gymkhana 2 fits all three. Never assume, though. Confirm the part explicitly lists your make and model year.
Installation and Care
A home install is a realistic weekend job. You need a socket set with extensions, wrenches, and penetrating oil for rusty factory bolts. Never work under a car held up by a jack alone — use jack stands. Exhaust components are heavy and awkward; a second set of hands helps.
A complete kit includes the pipes and muffler sections, tips, and the hardware to seal it: fresh gaskets and clamps. Lay everything out against the parts list before you start. If you would rather not do it on your back, a professional install is money well spent.
Care is simple. Inspect the system at every oil change. Check welds and hangers for cracks or damage, and confirm clamps and connections are still tight — vibration loosens hardware over time. Catch a small leak or a loose bolt early and it stays small.
Frequently Asked Questions
Do I need a tune after installing a new exhaust? Not for a cat-back or an axle-back — neither changes airflow enough to require one. A tune becomes mandatory when airflow changes at the front of the system, as with headers. Crawford does not sell tuning; a professional tuner handles that step.
What is the real performance difference between an axle-back and a cat-back? An axle-back changes sound and appearance. It keeps the stock mid-pipe, so there is no meaningful power gain. A cat-back replaces the piping from the converter back, reduces backpressure across the system, and produces more power and torque across the RPM range.
How do I get a good sound without being obnoxiously loud? Listen to recordings of the system on a BRZ at idle, under acceleration, and at cruise before you buy. Look for resonators designed to cancel drone. A valved system gives you both settings in one part.
Are more expensive systems worth it? Usually, yes. The price reflects materials — T304 stainless or titanium instead of mild steel — plus mandrel-bent piping, weld quality, and the engineering spent producing a strong tone without drone. Cheaper systems save money in exactly those places.
For the wider BRZ modification picture, see Subaru BRZ performance upgrades. Questions about fitment for your car: (855) 677-8243.