Boost Your Car's Performance with Billet Power Blocks

• Adds 19 HP / 15 TQ Under the Curve - No Tune Required

• Improves OEM Torque Dip by 300 RPM on a Totally Stock BRZ 

• Improves Acceleration

• Decreases Delay between Shifts with AT

• Increases the Volumetric Efficiency of your Intake Manifold

• Maximizes the Potential of Aftermarket Intakes

• Installs in an Hour or Less

"We feel that the Crawford Performance Power Blocks intake manifold spacer makes the largest non forced induction power gain of any single part we have tried to date."
          - MotoIQ 

Naturally Aspirated (N/A) vehicles are starving for air without a turbo. Sure, an aftermarket Intake / Cold-Air Intake will bring more air in, but without a bigger volume in your intake manifold to receive the extra air, the air flow essentially gets choked before it has a chance to enter the engine. 
The Crawford Billet Power Blocks raise your intake manifold, lengthening the intake runners. This increases the volumetric efficiency of your manifold, which provides optimum airflow so that your engine receives as much air as your intake (OEM or aftermarket) can throw at it. 
Tested on and off our Dynapack Chassis Dyno, we stacked plates up then back down until we found the sweet spot that makes your FA20 engine scream (in a good way)! 
Made from CNC'd Aluminum and anodized red, these spacers look incredible under the hood. The kit includes the 2 spacers, 4 Block Standoffs, 10 longer mounting bolts, 6 washers, 4 Derlin o-ring seals, a grounding bracket for the direct injection control unit and the nut/bolt to mount, as well as an extended PCV hose and fitting. 
The install can be completed in under an hour, and is rated a 3 out of 10 on install difficulty. 

If you choose to use E85 with our BPB's then you will see a larger increase in power and torque than if using pump gas. 

The BPB's are compatible with OEM or aftermarket intakes, tunes, and fuel. 

Note: We only recommend this upgrade on naturally aspirated setups. 

Note: For Off-Road Use Only

Click here for MotoIQ Review

Click here for Written Install Intructions
Click here for Installation Video

If your vehicle has high mileage (~100,000 miles), consider purchasing set of new Intake Manifold Gaskets with your order. If you reassemble your vehicle after installing the BPB's and receive CEL Code P050A, an air leak from your gaskets is most likely the cause. 

Full Fitment:

• 2013 Subaru BRZ

• 2014 Subaru BRZ

• 2015 Subaru BRZ

• 2016 Subaru BRZ

• 2017 Subaru BRZ

• 2018 Subaru BRZ

• 2019 Subaru BRZ

• 2020 Subaru BRZ

• 2021 Subaru BRZ

• 2013 Scion FR-S

• 2014 Scion FR-S

• 2015 Scion FR-S

• 2016 Scion FR-S

• 2013 Toyota GT86

• 2014 Toyota GT86

• 2015 Toyota GT86

• 2016 Toyota GT86

• 2017 Toyota GT86

• 2018 Toyota GT86

• 2019 Toyota GT86

• 2020 Toyota GT86

• 2021 Toyota GT86

• 2017 Toyota 86

• 2018 Toyota 86

• 2019 Toyota 86

• 2020 Toyota 86

• 2021 Toyota 86

Upgrade Your Subaru WRX/STI's Exhaust System

Sold as a Cat-Back system, this Cat-Back is designed to fit to OEM downpipe location

• Mid Pipe Length: 50" Flange to Flange

• Axle-Back Length: 48" Flange to Tip 

Our exhaust was originally designed for Ken Block's Gymkhana 1 2006 Subaru STI.

This exhaust was designed for Ken Block and the Subaru Gymkhana Cars, but was originally inspired by the Crawford Performance Time Attack Race Car with one main reason behind this system: to be heard. Crawford Performance came up with an exhaust design that adds reverberation to the sound. The result is a doubling of the sound amplitude in effort to make the exhaust audible over the rest of the race track. It produces a loud, but deep sounding rumble, unlike anything on the market.

Made from 304 stainless steel, and hand fabricated in-house. 3 inch body to 4.5 inch tip.

Do you have a RHD Impreza? The down pipes are different lengths between the USDM and RHD models, so the mid pipe section of this cat-back will not connect with an OEM RHD downpipe. If you purchase the full turbo-back system that includes this cat-back and our USDM downpipe, it will then fit. 

Sound Clips

Crawford Performance Intake Manifold Spacers / Billet Power Blocks (BPB) for 2018-2023 Subaru Crosstrek 2.0i & 2.5i

Increase your Subaru Crosstrek's Horsepower!

• Adds 15 HP / 22 TQ - No Tune Required

• Improves Acceleration

• Decreases Delay between Shifts with AT

• Increases the Volumetric Efficiency of your Intake Manifold

• Maximizes the Potential of Aftermarket Intakes

• Installs in three hours or less

• Raises intake manifold by 1-13/16" inches

• Stealth Black now available!

Naturally Aspirated (N/A) vehicles are starving for air without a turbo. Sure, an aftermarket Intake / Cold-Air Intake will bring more air in, but without a bigger volume in your intake manifold to receive the extra air, the air flow essentially gets choked before it has a chance to enter the engine. 
The Crawford Billet Power Blocks raise your intake manifold, lengthening the intake runners. This increases the volumetric efficiency of your manifold, which provides optimum airflow so that your engine receives as much air as your intake (OEM or aftermarket) can throw at it. 
Tested on and off our Dynapack Chassis Dyno, we stacked plates up then back down until we found the sweet spot that makes your FB20 engine scream (in a good way)! 
Made from CNC'd billet 6061 Aluminum and anodized red, these spacers look incredible under the hood. The kit includes the 2 spacers, 6 longer mounting bolts, 4 Viton 75 o-ring seals, a stainless steel extended EGR tube, as well as an extended PCV hose. 
The install can be completed within 3 hours, and is rated a 6 out of 10 on install difficulty. 

We recommend running mid-grade or premium fuel for the best results. 

The BPB's are compatible with OEM or aftermarket intakes, tunes, and higher octane fuels. 

Note: We only recommend this upgrade on naturally aspirated setups.

Note: For Off-Road Use Only 

If your vehicle has high mileage (~100,000 miles), consider purchasing set of new Intake Manifold Gaskets with your order. If you reassemble your vehicle after installing the BPB's and receive CEL Code P050A, an air leak from your gaskets is most likely the cause. 

Install Instructions

2.0i: Written PDF

2.5i: Written PDF

Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek

Crawford Performance Intake Manifold Spacers / Billet Power Blocks (BPB) for 2013 - 2017 Subaru XV Crosstrek 2.0i

• Adds 15 HP / 22 TQ - No Tune Required

• Improves Acceleration

• Decreases Delay between Shifts with AT

• Increases the Volumetric Efficiency of your Intake Manifold

• Maximizes the Potential of Aftermarket Intakes

• Installs in an Hour or Less

Naturally Aspirated (N/A) vehicles are starving for air without a turbo. Sure, an aftermarket Intake / Cold-Air Intake will bring more air in, but without a bigger volume in your intake manifold to receive the extra air, the air flow essentially gets choked before it has a chance to enter the engine. 
The Crawford Billet Power Blocks raise your intake manifold, lengthening the intake runners. This increases the volumetric efficiency of your manifold, which provides optimum airflow so that your engine receives as much air as your intake (OEM or aftermarket) can throw at it. 
Tested on and off our Dynapack Chassis Dyno, we stacked plates up then back down until we found the sweet spot that makes your FB20 engine scream (in a good way)! 
Made from CNC'd billet 6061 Aluminum and anodized red, these spacers look incredible under the hood. The kit includes the 2 spacers, 8 longer mounting bolts, 4 Derlin o-ring seals, a stainless steel extended EGR tube, as well as an extended PCV hose. 
The install can be completed in under an hour, and is rated a 3 out of 10 on install difficulty. 

We recommend running mid-grade or premium fuel for the best results. 

The BPB's are compatible with OEM or aftermarket intakes, tunes, and fuel. They are however not compatible with our Eco-Block, unless you are receiving a custom tune after install. 

Note: We only recommend this upgrade on naturally aspirated setups. 

Note: For Off-Road Use Only

If your vehicle has high mileage (~100,000 miles), consider purchasing set of new Intake Manifold Gaskets with your order. If you reassemble your vehicle after installing the BPB's and receive CEL Code P050A, an air leak from your gaskets is most likely the cause. 

Install Instructions

Written PDF Document
Video

Crawford Performance Air Oil Separator: The Subaru Original

Baja Edition for Subaru 2018+ Crosstrek 2.0i

• Not a Catch Can - Closed Loop and Maintenance Free

• Consume Less Oil

• Extend the Life of your Engine

• Reduce Detonation and Risk of Engine / Ringland Failure

• Reduce Fuel Dilution and Subsequent Power Loss

• Custom Colors available
• Default Color is Satin Black

New Baja Edition Features:

• Labyrinth within Baffled Chambers increase efficiency
• Does not delete Smog Component - Utilizes OEM PCV System
• 2 Lines = 10 minute Install!
• Tested on the Subaru-Backed Crosstrek Desert Racer for thousands of race miles

Oil pooling in your intake? Stop the oil from ever getting there with the Crawford Air Oil Separator.

The Crawford Performance Air Oil Separator (AOS) is the original solution to Subaru's notorious oiling system issues. Although the technology was pre-existing with other vehicle brands such as Porsche, Crawford Performance is the inventor of the first system specifically for Subaru. No other AOS on the market employs the same technology.

Want to know more about how an Air/Oil Separator works and why you need one? 

Click here to check out our FAQ blog on the technology inside. 
There you can also find a full fitment list for all current versions and kits.

Note: more fitment options are currently in R&D. Is your car or application unavailable? Click here to check our V2 Kits, which have the widest range of fitments. 

Install Instructions:
Please note! This kit can be installed with or without Power Blocks.
Default spacers are without Power Blocks!
Written PDF

Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek

Crawford Air Oil Separator Complete Install Kits

For those of you who have purchased one of our Air/Oil Separators used, or just want to refresh your current kit, here are all of the pieces for re-installation. Pieces and prices will vary for each application.

Need help identifying which full kit part number is meant for your canister or vehicle?

Below are the full kits listed based on the canister type. If your vehicle is not listed with the canister, then that means that the canister you have is meant to be mounted on a different vehicle or location. That being said, you may be able to retrofit the unit to your engine bay: just be sure to mount the canister so that the ports are higher than their connection points. 

Do you have the wrong canister for your vehicle or do you need to mount it in a different location?

This only applies to the V2 cans (6 port), but you can cut off the bracket and purchase the Universal Kit (S0712-1). It comes with 3 different brackets to choose from along with a clamp for holding it to the canister. If you don't want the look of a clamp around your canister, you can take your bracket of choice to a fab shop to have it welded on.

• S0692: 19+ Forester 2.5, 21+ Crosstrek 2.5, 20+ Legacy 2.5, 20+ Outback 2.5

• S0696: 2018+ Subaru Crosstrek

• S0698: 2013-2017 Subaru Crosstrek, 2012-2016 Subaru Impreza, 2014-2016 Subaru Forester (Non-Turbo)

• S0699: 2008+ STI, 2008-2014 WRX, 07-13 FXT with Top Mount Intercooler

• S0711: 2013+ Subaru BRZ, 2013-2016 Scion FR-S, 2013+ Toyota GT86, 2017+ Toyota 86

 

• S0712-1: Universal

  

• S0714-1: 02-07 WRX, 02-07 STI, 04-06 Forester XT with Top Mount Intercooler

 

• S0715-1: 02-07 WRX, 02-07 STI, 04-06 Forester XT with Front Mount Intercooler

• S0717: 15+ WRX, 14-18 Forester XT with Top Mount Intercooler (DIT). Original S0717 now discontinued: Same canister as shown with an additional 2 ports at the bottom. Contact us for a custom kit if you have one of the old versions with 6 ports.

Use our Crawford Performance Stickers to spice up your fridge, toolbox, or car!

(Price includes Continental US shipping via USPS First Class)

OEM Subaru Replacement Intake Manifold Gaskets

• New Genuine Subaru OEM Replacement 

• Sold as a pair. (1 for both the left and the right side) 

• Price Includes US Domestic Standard Shipping via USPS

A set of these gaskets come in our Short Block installation Kits, but are also a good idea to replace when installing our Billet Power Blocks (BPB's) while the manifold is disconnected. These are silicone gaskets, so they are reusable if not dry/cracked or deformed. If your gaskets don't look fresh, grab a set of these to install with your new BPB's. 

Crawford Performance Gymkhana 3 Axle Back Exhaust for 2018+ Subaru Crosstrek 

• 2 Crosstrek Exhaust Options: Muffler Delete & Muffler Replacement

• Bolts directly on to Stock Mid-Pipe (2.0")

• Perfect for those wanting to keep all Cats (Catalytic Converters) in place for Smog Legality

• Easy to swap with Stock Muffler / Exhaust

• Inspired by the Original Gymkhana One Exhaust

The Crawford Performance Subaru Crosstrek Axle Back Exhaust is a product that was inspired by the Crosstrek Desert Racer and our original Subaru Gymkhana videos. We've taken that inspiration and applied it to the Crosstrek to enhance their signature boxer engine sound like we have with many other Subaru models. The shrunk down megaphone design creates a distinct and hearty growl that imitates our race cars and invokes the spirit of speed expected from Crawford. We also gave you two options; a muffled version and a straight pipe version

Included Components:

• 1 Crawford Performance Crosstrek Exhaust
• Reuse existing hardware

Note: System bolts directly on to stock mid-pipe and this system has been tested to generate the same power levels as a exhaust free vehicle (no mid pipe, no axle back).

Specifications

Body measures: 2"

Tip measures: 9.75"

Tip diameter: 4" at widest (3.5" at outlet)

*Resonator: 8"

*Resonator only included in "with resonator" variant

Resonated 

Un-Resonated

Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek 

Crawford Performance Air Oil Separator V3
STI  2008-2021 w/ TMIC

Crawford Performance Air Oil Separator: The Subaru Original

• Not a Catch Can - Closed Loop and Maintenance Free

• Consume Less Oil

• Extend the Life of your Engine

• Reduce Detonation and Risk of Engine / Ringland Failure

• Reduce Fuel Dilution and Subsequent Power Loss

New Dual Chamber (V3) Features:

• Our Latest technology - Not seen anywhere else and Patent Pending
• Double Labyrinth Chambers increase efficiency
• Does not delete Smog Component - Utilizes OEM PCV System
• Worldwide Compatibility: Fits on RHD Vehicles
• No Coolant Line = Easier Install

Oil pooling in your intake? Stop the oil from ever getting there with the Crawford Air Oil Separator.

The Crawford Performance Air Oil Separator (AOS) is the original solution to Subaru's notorious oiling system issues. Although the technology was pre-existing with other vehicle brands such as Porsche, Crawford Performance is the inventor of the first system specifically for Subaru. No other AOS on the market employs the same technology.

Want to know more about how an Air/Oil Separator works and why you need one? 

Click here to check out our FAQ blog on the technology inside. 
There you can also find a full fitment list for all current versions and kits.

Note: more V3 fitment options are currently in R&D. Is your car or application unavailable? Click here to check our V2 Kits, which have the widest range of fitments. 

*Note: Due to the fact that the AOS bracket connects to the TGV housing, this kit is not compatible with aftermarket TGV housings. 

*Note: This system was designed on USD models. Not compatible with all PCV systems across the world and may require some additional components to properly install.

Install Instructions

2008 - 2016 STI
     PDF
     Video

2017+ STI
     PDF
     Video

Upgrade Your Light Wiring Harness with Crawford Performance Circuit Board

• Circuit Board used on the Crawford Off-Road Subaru Crosstrek Build
• Powder coated steel plate designed to hold all fuses and relays for the Crawford light wiring harnesses
• Mounts off of battery brace for easy installation of harnesses
• Bracket provides a clean finish and minimizes wire clusters for easier maintenance and installation of components

Our integrated lighting circuit harness fits seamlessly into the engine bay to provide a secure point to mount the Crawford light wiring harnesses. Easy installation and access mean less trouble installing wires and a cleaner finished product when the job is done!

 Included Components:

• One Crawford Performance Circuit Board for Light Wiring Harness

If you are looking to improve the performance of your vehicle's lighting system, then Crawford Performance Circuit Board for Light Wiring Harnesses is what you need. This circuit board is designed to enhance the efficiency of your light wiring system by reducing the voltage drop and increasing the current flow.

Made from high-quality materials, Crawford Performance Circuit Board is durable and can withstand the rigors of daily use. The board is designed to be easy to install and comes with all the necessary components to ensure a hassle-free installation process.

One of the significant advantages of using Crawford Performance Circuit Board is its ability to reduce the electrical resistance of your light wiring system. By reducing the resistance, the current flow increases, resulting in brighter lights with better illumination. This means you can see better in low light conditions and improve your overall driving safety.

Dual Chamber (V3) for Subaru WRX: 2015 + w/ TMIC (Only fits with Top Mount Intercooler) 

Crawford Performance Air Oil Separator: 
The Subaru Original

• Not a Catch Can - Closed Loop and Maintenance Free

• Consume Less Oil

• Extend the Life of your Engine

• Reduce Detonation and Risk of Engine / Ringland Failure

• Reduce Fuel Dilution and Subsequent Power Loss

New Dual Chamber (V3) Features:

• Our Latest technology - Not seen anywhere else and Patent Pending
• Double Labyrinth Chambers increase efficiency
• Does not delete Smog Component - Utilizes OEM PCV System
• Worldwide Compatibility: Fits on RHD Vehicles
• No Coolant Line = Easier Install

Oil pooling in your intake? Stop the oil from ever getting there with the Crawford Air Oil Separator.

The Crawford Performance Air Oil Separator (AOS) is the original solution to Subaru's notorious oiling system issues. Although the technology was pre-existing with other vehicle brands such as Porsche, Crawford Performance is the inventor of the first system specifically for Subaru. No other AOS on the market employs the same technology.

Want to know more about how an Air/Oil Separator works and why you need one? 

Click here to check out our FAQ blog on the technology inside. 
There you can also find a full fitment list for all current versions and kits.

Note: more V3 fitment options are currently in R&D. Is your car or application unavailable? Click here to check our V2 Kits, which have the widest range of fitments. 

Install Instructions

This piece comes in the Air/Oil Separator Kits for EJ applications. Due to frequent requests for a replacement, we offer it separately. It is included in the following kits:

• S0712-1
• S0714-1
• S0715-1
• S0720
• S0720-1

Crawford Performance Air Oil Separator: 
The Subaru Original
Baja Edition for 2013-2017 Subaru XV Crosstrek 2.0i

• Not a Catch Can - Closed Loop and Maintenance Free

• Consume Less Oil

• Extend the Life of your Engine

• Reduce Detonation and Risk of Engine / Ringland Failure

• Reduce Fuel Dilution and Subsequent Power Loss

New Baja Edition Features:

• Labyrinth within Baffled Chambers increase efficiency
• Does not delete Smog Component - Utilizes OEM PCV System
• 2 Lines = 10 minute Install!
• Tested on the Subaru-Backed Crosstrek Desert Racer for thousands of race miles

Oil pooling in your intake? Stop the oil from ever getting there with the Crawford Air Oil Separator.

The Crawford Performance Air Oil Separator (AOS) is the original solution to Subaru's notorious oiling system issues. Although the technology was pre-existing with other vehicle brands such as Porsche, Crawford Performance is the inventor of the first system specifically for Subaru. No other AOS on the market employs the same technology.

Want to know more about how an Air Oil Separator works and why you need one? 

Click here to check out our FAQ blog on the technology inside. 
There you can also find a full fitment list for all current versions and kits.

Note: more fitment options are currently in R&D. Is your car or application unavailable? Click here to check our V2 Kits, which have the widest range of fitments. 

Install Instructions

Crawford Performance Air Oil Separator V2 - WRX 2002-2007

Crawford Performance Air Oil Separator: The Subaru Original

• Not a Catch Can - Closed Loop and Maintenance Free

• Consume Less Oil

• Extend the Life of your Engine

• Reduce Detonation and Risk of Engine / Ringland Failure

• Reduce Fuel Dilution and Subsequent Power Loss

Oil pooling in your intake? Stop the oil from ever getting there with the Crawford Air Oil Separator. 

The Crawford Performance Air Oil Separator (AOS) is the original solution to Subaru's notorious oiling system issues. Although the technology was pre-existing with other vehicle brands such as Porsche, Crawford Performance is the inventor of the first system specifically for Subaru. No other AOS on the market employs the same technology.

Notes: For Off-Road Use Only

Want to know more about how an Air/Oil Separator works and why you need one? 

Click here to check out our FAQ blog on the technology inside. 
There you can also find a full fitment list for all current versions and kits.

Also check out our latest technology with patent pending:
The Crawford Performance Dual Chamber AOS (V3)

This item is non-returnable at sale pricing.

Upgrade Your 2012-2016 Impreza 2.0 with Crawford Performance Billet Power Blocks

Crawford Performance Intake Manifold Spacers / Billet Power Blocks (BPB) for 2012 - 2016 Subaru Impreza 2.0i

• Adds 15 HP / 22 TQ - No Tune Required

• Improves Acceleration

• Decreases Delay between Shifts with AT

• Increases the Volumetric Efficiency of your Intake Manifold

• Maximizes the Potential of Aftermarket Intakes

• Installs in an Hour or Less

Naturally Aspirated (N/A) vehicles are starving for air without a turbo. Sure, an aftermarket Intake / Cold-Air Intake will bring more air in, but without a bigger volume in your intake manifold to receive the extra air, the air flow essentially gets choked before it has a chance to enter the engine. 
The Crawford Billet Power Blocks raise your intake manifold, lengthening the intake runners. This increases the volumetric efficiency of your manifold, which provides optimum airflow so that your engine receives as much air as your intake (OEM or aftermarket) can throw at it. 
Tested on and off our Dynapack Chassis Dyno, we stacked plates up then back down until we found the sweet spot that makes your FB20 engine scream (in a good way)! 
Made from CNC'd billet 6061 Aluminum and anodized red, these spacers look incredible under the hood. The kit includes the 2 spacers, 8 longer mounting bolts, 4 Derlin o-ring seals, a stainless steel extended EGR tube, as well as an extended PCV hose. 
The install can be completed in under an hour, and is rated a 3 out of 10 on install difficulty. 

We recommend running mid-grade or premium fuel for the best results. 

The BPB's are compatible with OEM or aftermarket intakes, tunes, and fuel. They are however not compatible with our Eco-Block, unless you are receiving a custom tune after install. 

Note: We only recommend this upgrade on naturally aspirated setups. 

Note: For Off-Road Use Only

If your vehicle has high mileage (~100,000 miles), consider purchasing set of new Intake Manifold Gaskets with your order. If you reassemble your vehicle after installing the BPB's and receive CEL Code P050A, an air leak from your gaskets is most likely the cause. 

Install Instructions

Written PDF Document
Video

Upgrade Your 2021-2023 Crosstrek 2.5 with Crawford Air Oil Separator Baja

• Not a Catch Can - Closed Loop and Maintenance Free

• Consume Less Oil

• Extend the Life of your Engine

• Reduce Detonation and Risk of Engine / Ringland Failure

• Reduce Fuel Dilution and Subsequent Power Loss

• Custom Colors Available, message for details.

• Default color is Satin Black

New Baja Features:

• Labyrinth within Baffled Chambers increase efficiency

• Does not delete Smog Component - Utilizes OEM PCV System

• 2 Lines = 10 minute Install!

• Tested on the Subaru-Backed Crosstrek Desert Racer for thousands of race miles

Oil pooling in your intake? Stop the oil from ever getting there with the Crawford Air Oil Separator.

The Crawford Performance Air Oil Separator (AOS) is the original solution to Subaru's notorious oiling system issues. Although the technology was pre-existing with other vehicle brands such as Porsche, Crawford Performance is the inventor of the first system specifically for Subaru. No other AOS on the market employs the same technology.

Want to know more about how an Air/Oil Separator works and why you need one? 

Click here to check out our FAQ blog on the technology inside. 
There you can also find a full fitment list for all current versions and kits.

Note: more fitment options are currently in R&D. Is your car or application unavailable? Click here to check our V2 Kits, which have the widest range of fitments. 

Install Instructions
Written PDF

Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek

If you want to enhance the performance of your 2021-2023 Crosstrek 2.5, the Crawford Air Oil Separator Baja is a must-have car accessory. This product is specifically designed for this vehicle model and can help prevent blow-by gases from entering the engine's intake system, which reduces the engine's efficiency. This separator is the perfect solution for car enthusiasts who want to enhance their vehicle's performance.

This air oil separator is made of high-quality materials, which makes it a durable and long-lasting accessory for your Crosstrek. It comes with a unique design that separates oil and air efficiently, ensuring maximum performance. Installation is easy, and the separator comes with mounting hardware and hoses, making the whole process hassle-free.

The Crawford Air Oil Separator Baja improves engine performance by reducing engine knock and improving fuel economy. It keeps the intake system cleaner, which also helps to extend the engine's life. By keeping the blow-by gases out of your engine's intake system, you'll enjoy smoother acceleration and a more responsive throttle.

In conclusion, the Crawford Air Oil Separator Baja is a high-quality car accessory that can help improve your 2021-2023 Crosstrek 2.5's performance. It's easy to install and comes with everything you need to get started. Whether you're a car enthusiast or just want to keep your vehicle running efficiently, this air oil separator is a great investment.

Crawford Performance Mirror Light Pod Brackets for 2018+ Subaru Crosstrek

• Sold as a pair

• Light mount brackets are powder-coated for durability and corrosion resistance 

• Maintains OEM look through integrated vehicle mounting

• Simple installation takes 15 minutes

• Adds an aggressive rally style look while improving nighttime and fog visibility

The Crawford Performance Mirror Light Pod Brackets are inspired by the Subaru of America Crosstrek Desert Racer, with the simple goal of lighting up any path you choose to conquer in your Crosstrek. Our mirror light brackets can be coupled with with your choice of LED cube pod light or with our 90 degree LED light pods. Our pods allow for full vision from side to side of the vehicle, providing security and assurance that nothing will take you by surprise during your nighttime off-roading.    

Included Components:

• Two powder-coated mirror mounting brackets 
• All necessary mounting hardware

Note: Light pods purchased separately here: Light Pods or purchase the full kit here: Mirror Light Pod Kit

Installation Instructions:

Written Instructions

Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek

Crawford Performance Intake Manifold Spacers / Billet Power Blocks (BPB) for 2017+ Subaru Impreza 2.0i

• Adds 15 HP / 22 TQ - No Tune Required

• Improves Acceleration

• Decreases Delay between Shifts with AT

• Increases the Volumetric Efficiency of your Intake Manifold

• Maximizes the Potential of Aftermarket Intakes

• Installs in an three hours or less

• raises intake manifold by 1-13/16" inches
  

• Stealth Black now available!

Naturally Aspirated (N/A) vehicles are starving for air without a turbo. Sure, an aftermarket Intake / Cold-Air Intake will bring more air in, but without a bigger volume in your intake manifold to receive the extra air, the air flow essentially gets choked before it has a chance to enter the engine. 
The Crawford Billet Power Blocks raise your intake manifold, lengthening the intake runners. This increases the volumetric efficiency of your manifold, which provides optimum airflow so that your engine receives as much air as your intake (OEM or aftermarket) can throw at it. 
Tested on and off our Dynapack Chassis Dyno, we stacked plates up then back down until we found the sweet spot that makes your FB20 engine scream (in a good way)! 
Made from CNC'd billet 6061 Aluminum and anodized red, these spacers look incredible under the hood. The kit includes the 2 spacers, 6 longer mounting bolts, 4 Viton 75 o-ring seals, a stainless steel extended EGR tube, as well as an extended PCV hose. 
The install can be completed within 3 hours, and is rated a 6 out of 10 on install difficulty. 

We recommend running mid-grade or premium fuel for the best results. 

The BPB's are compatible with OEM or aftermarket intakes, tunes, and higher octane fuels.

We recommend running mid-grade or premium fuel for the best results. 

The BPB's are compatible with OEM or aftermarket intakes, tunes, and fuel. 

Note: We only recommend this upgrade on naturally aspirated setups. 

Note: For Off-Road Use Only

If your vehicle has high mileage (~100,000 miles), consider purchasing set of new Intake Manifold Gaskets with your order. If you reassemble your vehicle after installing the BPB's and receive CEL Code P050A, an air leak from your gaskets is most likely the cause. 

Install Instructions

Written PDF

Crawford Performance Hood Light Pod Brackets for 2018+ Subaru Crosstrek: 

• Will accept most light pod styles

• Light mount brackets are powder-coated for durability and corrosion resistance 

• Simple installation and does not require hood to be removed

• Adds an aggressive rally style look while improving nighttime and fog visibility

• Call in for Custom Powder Coat Options

• Sold as pair

• Will limit hood movement (Can still utilize 1st hood prop point) 

The Crawford Performance Hood Light Pod Brackets are inspired by the Subaru of America Crosstrek Desert Racer, with the simple goal of lighting up any path you choose to conquer in your Crosstrek. Our hood light brackets also known as a ditch light can be coupled with with your choice of LED cube pod light or with our 90 degree LED light pods. Our pods allow for full vision from side to side of the vehicle, providing security and assurance that nothing will take you by surprise during your night time off-roading.    

Included Components:

• Two powder-coated hood mounting brackets 
• All necessary mounting hardware

Note: Light pods purchased separately here: Light Pods or purchase the full kit here: Hood Light Pod Kit

Installation Instructions:

Written Instructions

Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek