Crawford Performance Intake Manifold Spacers / Billet Power Blocks (BPB) for 2018-2023 Subaru Crosstrek 2.0i & 2.5i

Increase your Subaru Crosstrek's Horsepower!

• Adds 15 HP / 22 TQ - No Tune Required

• Improves Acceleration

• Decreases Delay between Shifts with AT

• Increases the Volumetric Efficiency of your Intake Manifold

• Maximizes the Potential of Aftermarket Intakes

• Installs in three hours or less

• Raises intake manifold by 1-13/16" inches

• Stealth Black now available!

Naturally Aspirated (N/A) vehicles are starving for air without a turbo. Sure, an aftermarket Intake / Cold-Air Intake will bring more air in, but without a bigger volume in your intake manifold to receive the extra air, the air flow essentially gets choked before it has a chance to enter the engine. 
The Crawford Billet Power Blocks raise your intake manifold, lengthening the intake runners. This increases the volumetric efficiency of your manifold, which provides optimum airflow so that your engine receives as much air as your intake (OEM or aftermarket) can throw at it. 
Tested on and off our Dynapack Chassis Dyno, we stacked plates up then back down until we found the sweet spot that makes your FB20 engine scream (in a good way)! 
Made from CNC'd billet 6061 Aluminum and anodized red, these spacers look incredible under the hood. The kit includes the 2 spacers, 6 longer mounting bolts, 4 Viton 75 o-ring seals, a stainless steel extended EGR tube, as well as an extended PCV hose. 
The install can be completed within 3 hours, and is rated a 6 out of 10 on install difficulty. 

We recommend running mid-grade or premium fuel for the best results. 

The BPB's are compatible with OEM or aftermarket intakes, tunes, and higher octane fuels. 

Note: We only recommend this upgrade on naturally aspirated setups.

Note: For Off-Road Use Only 

If your vehicle has high mileage (~100,000 miles), consider purchasing set of new Intake Manifold Gaskets with your order. If you reassemble your vehicle after installing the BPB's and receive CEL Code P050A, an air leak from your gaskets is most likely the cause. 

Install Instructions

2.0i: Written PDF

2.5i: Written PDF

Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek

Crawford Performance Air Oil Separator: The Subaru Original

Baja Edition for Subaru 2018+ Crosstrek 2.0i

• Not a Catch Can - Closed Loop and Maintenance Free

• Consume Less Oil

• Extend the Life of your Engine

• Reduce Detonation and Risk of Engine / Ringland Failure

• Reduce Fuel Dilution and Subsequent Power Loss

• Custom Colors available
• Default Color is Satin Black

New Baja Edition Features:

• Labyrinth within Baffled Chambers increase efficiency
• Does not delete Smog Component - Utilizes OEM PCV System
• 2 Lines = 10 minute Install!
• Tested on the Subaru-Backed Crosstrek Desert Racer for thousands of race miles

Oil pooling in your intake? Stop the oil from ever getting there with the Crawford Air Oil Separator.

The Crawford Performance Air Oil Separator (AOS) is the original solution to Subaru's notorious oiling system issues. Although the technology was pre-existing with other vehicle brands such as Porsche, Crawford Performance is the inventor of the first system specifically for Subaru. No other AOS on the market employs the same technology.

Want to know more about how an Air/Oil Separator works and why you need one? 

Click here to check out our FAQ blog on the technology inside. 
There you can also find a full fitment list for all current versions and kits.

Note: more fitment options are currently in R&D. Is your car or application unavailable? Click here to check our V2 Kits, which have the widest range of fitments. 

Install Instructions:
Please note! This kit can be installed with or without Power Blocks.
Default spacers are without Power Blocks!
Written PDF

Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek

Crawford Performance Gymkhana 3 Axle Back Exhaust for 2018+ Subaru Crosstrek 

• 2 Crosstrek Exhaust Options: Muffler Delete & Muffler Replacement

• Bolts directly on to Stock Mid-Pipe (2.0")

• Perfect for those wanting to keep all Cats (Catalytic Converters) in place for Smog Legality

• Easy to swap with Stock Muffler / Exhaust

• Inspired by the Original Gymkhana One Exhaust

The Crawford Performance Subaru Crosstrek Axle Back Exhaust is a product that was inspired by the Crosstrek Desert Racer and our original Subaru Gymkhana videos. We've taken that inspiration and applied it to the Crosstrek to enhance their signature boxer engine sound like we have with many other Subaru models. The shrunk down megaphone design creates a distinct and hearty growl that imitates our race cars and invokes the spirit of speed expected from Crawford. We also gave you two options; a muffled version and a straight pipe version

Included Components:

• 1 Crawford Performance Crosstrek Exhaust
• Reuse existing hardware

Note: System bolts directly on to stock mid-pipe and this system has been tested to generate the same power levels as a exhaust free vehicle (no mid pipe, no axle back).

Specifications

Body measures: 2"

Tip measures: 9.75"

Tip diameter: 4" at widest (3.5" at outlet)

*Resonator: 8"

*Resonator only included in "with resonator" variant

Resonated 

Un-Resonated

Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek 

Upgrade Your Light Wiring Harness with Crawford Performance Circuit Board

• Circuit Board used on the Crawford Off-Road Subaru Crosstrek Build
• Powder coated steel plate designed to hold all fuses and relays for the Crawford light wiring harnesses
• Mounts off of battery brace for easy installation of harnesses
• Bracket provides a clean finish and minimizes wire clusters for easier maintenance and installation of components

Our integrated lighting circuit harness fits seamlessly into the engine bay to provide a secure point to mount the Crawford light wiring harnesses. Easy installation and access mean less trouble installing wires and a cleaner finished product when the job is done!

 Included Components:

• One Crawford Performance Circuit Board for Light Wiring Harness

If you are looking to improve the performance of your vehicle's lighting system, then Crawford Performance Circuit Board for Light Wiring Harnesses is what you need. This circuit board is designed to enhance the efficiency of your light wiring system by reducing the voltage drop and increasing the current flow.

Made from high-quality materials, Crawford Performance Circuit Board is durable and can withstand the rigors of daily use. The board is designed to be easy to install and comes with all the necessary components to ensure a hassle-free installation process.

One of the significant advantages of using Crawford Performance Circuit Board is its ability to reduce the electrical resistance of your light wiring system. By reducing the resistance, the current flow increases, resulting in brighter lights with better illumination. This means you can see better in low light conditions and improve your overall driving safety.

Upgrade Your 2021-2023 Crosstrek 2.5 with Crawford Air Oil Separator Baja

• Not a Catch Can - Closed Loop and Maintenance Free

• Consume Less Oil

• Extend the Life of your Engine

• Reduce Detonation and Risk of Engine / Ringland Failure

• Reduce Fuel Dilution and Subsequent Power Loss

• Custom Colors Available, message for details.

• Default color is Satin Black

New Baja Features:

• Labyrinth within Baffled Chambers increase efficiency

• Does not delete Smog Component - Utilizes OEM PCV System

• 2 Lines = 10 minute Install!

• Tested on the Subaru-Backed Crosstrek Desert Racer for thousands of race miles

Oil pooling in your intake? Stop the oil from ever getting there with the Crawford Air Oil Separator.

The Crawford Performance Air Oil Separator (AOS) is the original solution to Subaru's notorious oiling system issues. Although the technology was pre-existing with other vehicle brands such as Porsche, Crawford Performance is the inventor of the first system specifically for Subaru. No other AOS on the market employs the same technology.

Want to know more about how an Air/Oil Separator works and why you need one? 

Click here to check out our FAQ blog on the technology inside. 
There you can also find a full fitment list for all current versions and kits.

Note: more fitment options are currently in R&D. Is your car or application unavailable? Click here to check our V2 Kits, which have the widest range of fitments. 

Install Instructions
Written PDF

Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek

If you want to enhance the performance of your 2021-2023 Crosstrek 2.5, the Crawford Air Oil Separator Baja is a must-have car accessory. This product is specifically designed for this vehicle model and can help prevent blow-by gases from entering the engine's intake system, which reduces the engine's efficiency. This separator is the perfect solution for car enthusiasts who want to enhance their vehicle's performance.

This air oil separator is made of high-quality materials, which makes it a durable and long-lasting accessory for your Crosstrek. It comes with a unique design that separates oil and air efficiently, ensuring maximum performance. Installation is easy, and the separator comes with mounting hardware and hoses, making the whole process hassle-free.

The Crawford Air Oil Separator Baja improves engine performance by reducing engine knock and improving fuel economy. It keeps the intake system cleaner, which also helps to extend the engine's life. By keeping the blow-by gases out of your engine's intake system, you'll enjoy smoother acceleration and a more responsive throttle.

In conclusion, the Crawford Air Oil Separator Baja is a high-quality car accessory that can help improve your 2021-2023 Crosstrek 2.5's performance. It's easy to install and comes with everything you need to get started. Whether you're a car enthusiast or just want to keep your vehicle running efficiently, this air oil separator is a great investment.

Crawford Performance Mirror Light Pod Brackets for 2018+ Subaru Crosstrek

• Sold as a pair

• Light mount brackets are powder-coated for durability and corrosion resistance 

• Maintains OEM look through integrated vehicle mounting

• Simple installation takes 15 minutes

• Adds an aggressive rally style look while improving nighttime and fog visibility

The Crawford Performance Mirror Light Pod Brackets are inspired by the Subaru of America Crosstrek Desert Racer, with the simple goal of lighting up any path you choose to conquer in your Crosstrek. Our mirror light brackets can be coupled with with your choice of LED cube pod light or with our 90 degree LED light pods. Our pods allow for full vision from side to side of the vehicle, providing security and assurance that nothing will take you by surprise during your nighttime off-roading.    

Included Components:

• Two powder-coated mirror mounting brackets 
• All necessary mounting hardware

Note: Light pods purchased separately here: Light Pods or purchase the full kit here: Mirror Light Pod Kit

Installation Instructions:

Written Instructions

Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek

Crawford Performance Hood Light Pod Brackets for 2018+ Subaru Crosstrek: 

• Will accept most light pod styles

• Light mount brackets are powder-coated for durability and corrosion resistance 

• Simple installation and does not require hood to be removed

• Adds an aggressive rally style look while improving nighttime and fog visibility

• Call in for Custom Powder Coat Options

• Sold as pair

• Will limit hood movement (Can still utilize 1st hood prop point) 

The Crawford Performance Hood Light Pod Brackets are inspired by the Subaru of America Crosstrek Desert Racer, with the simple goal of lighting up any path you choose to conquer in your Crosstrek. Our hood light brackets also known as a ditch light can be coupled with with your choice of LED cube pod light or with our 90 degree LED light pods. Our pods allow for full vision from side to side of the vehicle, providing security and assurance that nothing will take you by surprise during your night time off-roading.    

Included Components:

• Two powder-coated hood mounting brackets 
• All necessary mounting hardware

Note: Light pods purchased separately here: Light Pods or purchase the full kit here: Hood Light Pod Kit

Installation Instructions:

Written Instructions

Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek

• Fits both 2.0L & 2.5L models
• Has Oil Drain Hole
• Made with 3/16" Laser cut aluminum
• Polished finish
• Offers full protection for your engine and front undercarriage
• Rear edge of the skid plate is up-turned, eliminating hang ups when reversing
• Improves aerodynamics and airflow
• Does not reduce radiator or cooling system efficiency

The Crawford Performance Front Skid Plate is inspired by the Subaru of America Crosstrek Desert Racer. Our front skid plate allows you to travel off-road knowing your motor will be fully protected from any rocks or debris the trail may throw in your way. Overland smart and keep your underbody protected today!

Included Components:

• Crawford CDR Series Front Skid Plate
• Mounting hardware

Installation Instructions:

Written Instructions

Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek

If you're looking for a reliable way to protect the motor of your 2018-2023 Subaru Crosstrek from all kinds of hazards, the Crawford Performance Front Motor Skid Plate is the perfect solution. Made from high-quality materials, this skid plate will ensure that your car's motor remains safe and sound, even in the toughest conditions.

One of the biggest advantages of the Crawford Performance Front Motor Skid Plate is its durability. This skid plate is made from heavy-duty materials that are designed to last for years without showing any signs of wear and tear. Whether you're driving on rough terrain or encountering obstacles on the road, you can trust this skid plate to provide superior protection for your car's motor.

Another benefit of this skid plate is its easy installation process. You don't need any special tools or skills to install the Crawford Performance Front Motor Skid Plate on your Crosstrek. Simply follow the instructions provided, and you'll be able to install it in minutes.

In addition to its durability and easy installation process, the Crawford Performance Front Motor Skid Plate also looks great on your Crosstrek. Its sleek and stylish design will enhance the overall appearance of your car, making it look more rugged and ready for adventure.

Crawford Performance 2 inch Lift Kit 2018-2023 Subaru Crosstrek

FMVSS 126 Compliant!

• Also fits the 2018+ Subaru Crosstrek Hybrid!

• Provides 2" front lift and 1.5" rear lift for a perfect leveled look 

• Billet CNC Aluminum coilover spacer built for strength and corrosion resistance

• Sway bar link extensions maintain factory sway bar positioning

• Maintains OEM ABS sensors and brake line mounts

• This suspension lift kit allows for larger tires 

• Easy, bolt on installation 

The Crawford Performance 2" Lift kit is inspired by theSubaru of America Crosstrek Desert Racer and is made to take you places you wouldn't otherwise been able to go. Enhance your off-roading experience and worry less about high-centering or damaging your undercarriage with the best Subaru Crosstrek lift kit!

Included Lift Kit Components:

• Two 2" aluminum strut spacers (front)
  
• Two 1.5" aluminum strut spacers (rear)
• Six long strut extensions (front) - M10 x 1.25
• Four short strut extensions (rear) - M10 x 1.25
• All necessary hardware

Note: Re-alignment will be required after installation

Install Instructions:

Written PDF

Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek

Crawford Performance Transmission Skid Plate for 2018-2023 Subaru Crosstrek

• Made with 3/16" laser cut aluminum

• Polished finish

• Does not require our front skid plate for installation

• Mounts directly to existing sub frame for maximum rigidity 

• Offers full protection for your transmission and transmission oil pan from rocks and debris

• Flush fit design eliminates hang-ups when reversing

The Crawford Performance Transmission Skid Plate is inspired by the Subaru of America Crosstrek Desert Racer. Our transmission plate allows you to travel off-road knowing your trans will be fully protected from any rocks or debris the trail may throw in your way. The laser cut design assures a clean fit and provides the structural rigidity needed to keep your overland trip going. Off-road smart and keep your underbody protected today with our trans plate!

Included Components:

• Crawford Performance Transmission Skid Plate for 2018+ Subaru Crosstrek

Cross-Platform Compatibility:

- Crosstrek: 2018-2023

- Forester: 2019-2025

- Impreza: 2017-2023

- Outback (non-XT): 2020-2025

Installation Instructions:

Written Instructions

Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek

Crawford Performance Mirror Light Pod Kit for 2018-2023 Subaru Crosstrek

• 90 degree LED cube pods included (comes as pair) 
  

• Light mount brackets are included and are powder-coated for durability and corrosion resistance 
  

• Maintains OEM look through integrated vehicle mounting

• Includes pre-measured wiring harness

• Adds an aggressive rally style look while improving nighttime and fog visibility

Note: The Crawford Circuit Board Bracket is a recommended option to ensure the wiring fits cleanly and enough wire length is usable  

The Crawford Performance Mirror Light Pod Kit is inspired by the Subaru of America Crosstrek Desert Racer, with the simple goal of lighting up any path you choose to conquer in your Crosstrek. Our mirror light brackets coupled with our 90 degree LED light pods allow for full vision from side to side of the vehicle. Providing security and assurance that nothing will take you by surprise during your nighttime off-roading.    

Included Mirror Light Kit Components:

• Two powder-coated mirror mounting brackets 
  
• Two 90 degree LED Light pods
• Wiring harness and switch
• All necessary mounting hardware

Light Specifications:

• 90º pods are 45w each resulting in 3.75a @ 12v
• 3600 lumens from each pod cube

Installation Instructions:

Written PDF

Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek

Crawford Legacy T-Shirt

Brand: Alstyle

Material: 100% Cotton

Fit: Adult Traditional

Crawford Performance Rock Sliders for 2018-2023 Subaru Crosstrek

• Adds protection from rocks and enhances off-road capabilities

• Rock Slider Kit provides complete fender to fender coverage

• Rugged design inspired by the Subaru Crosstrek Desert Racer

• Easy installation, bolts directly to OEM subframe with included hardware

• Custom Colors available. Contact us for details

• Sold as a set of 2

The Crawford Performance Rock Guards / Rock Sliders are inspired by the Subaru of America Crosstrek Desert Racer, and provide the best rock protection possible during your off-road adventures. We took the rugged look of the CDR and channeled it into the production Crosstrek to elevate its off-road performance. Our side nerfs let you take the trails by storm and worry less about damaging your rocker panels so you can focus on enjoying the ride.

*Please note these are built for side nerf protection as well as underneath protection from rocks. They are not designed to be side steps or running boards. 

Included Components:

• Pair of Crawford Performance Rock Guards

• Two 1.5" frame spacers

• Two 19mm rear mounting bolts

Note: Rear sub-frame spacers mounted between guard mount and sub-frame

Nerf Bar Specifications:

Lower Rock Guard Bar: 1.5" x .120 wall tubing

Upper Rock Guard Bar: 1.0" x .90 wall tubing

Front Guard mount bolt: OEM

Rear Guard mount bolt: M14 x 200 mm *compatible with other lift kits

Installation Instructions:
Written Instructions

Check out our Full Crosstrek Build Here:
https://crawfordperformance.com/pages/cpi-built-crosstrek

Why You Need a Crawford Performance Skid Plate

Crawford Performance Rear Differential Skid Plate for 2013+ Subaru Crosstrek

• Made with 3/16" laser cut aluminum
• Polished finish
• Mounts directly to existing sub frame for maximum rigidity 
• Offers full protection for your rear differential  
• Allows access to differential service ports for easy diff fluid changes

The Crawford Performance Rear Differential Skid Plate is inspired by the Subaru of America Crosstrek Desert Racer. Our skid plate allows you to travel off-road knowing your differential will be fully protected from any rocks or debris the trail may throw in your way. The laser cut design assures a clean fit without compromising the rear diff mounting points. Overland smart and keep your underbody protected today!

Included Components:

• Crawford Performance Rear Differential Skid Plate for 2013+ Subaru Crosstrek
• Mounting Hardware

Cross-Platform Compatibility:

- Subaru Crosstrek 2013-2023

- Subaru Forester 2009-2025

- Subaru Outback 2010-2015

Installation Instructions:

Written Instructions

Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek

If you're someone who often drives on rough terrain or off-road, a skid plate is a must-have accessory for your Subaru Crosstrek. The skid plate is a protective panel that is mounted on the underside of your car's engine. Its purpose is to protect the engine from damage caused by rocks, debris, and other obstacles on the road. A skid plate can help prevent costly repairs and keep your engine functioning properly. Crawford Performance Front Motor Skid Plate is one of the best skid plates available for Subaru Crosstrek, and here's why:

1. Superior Build Quality:

Crawford Performance Skid Plate is made from high-quality materials that are designed to withstand the toughest conditions. The skid plate is made from 3/16” 5052 aluminum, which is lightweight yet extremely strong. The plate is then powder coated for added durability and resistance to corrosion and rust.

2. Custom Fit:

The Crawford Performance Skid Plate is designed specifically for 2018-2023 Subaru Crosstrek, which means it fits perfectly and offers maximum protection. The plate is engineered to follow the contours of your car's undercarriage, providing complete coverage and no exposed seams or gaps.

3. Easy Installation:

Installing the Crawford Performance Skid Plate is a breeze. The plate comes with all the hardware you need and can be installed with simple hand tools. There's no need for special equipment or professional installation.

Overall, the Crawford Performance Front Motor Skid Plate is a must-have for any off-road enthusiast or anyone who wants to protect their car's engine. It's a durable, custom-fit skid plate that offers superior protection and is easy to install. Order yours today and enjoy a worry-free driving experience!

Crawford Performance Front Bumper Guard 2018-2023 Subaru Crosstrek

• Protects front end and front bumper from damage and adds rally style look to vehicle

• Powder coated for extra durability and corrosion resistance 

• Four bolt installation to sub frame requires no modifications to vehicle

• Design incorporates three rally style led light mounts

• Designed to work with either OEM or Crawford Skid Plates

• Call in for Custom Powder Coat Options

The Crawford Performance Subaru Crosstrek Front Bumper Guard was inspired by the Subaru of America Crosstrek Desert Racer, with both functionality and style in mind. Whether you are driving down the street or overlanding a trail, our off-road bumper is made to guard your Crosstrek and give you piece of mind. Built in mounts allow for up to three KC HiLites LED Slim Lights to ensure you will be able to see the road ahead in true rally fashion.     

Included Components:

• One Crawford Front Off-Road Bumper Guard
• All necessary mounting hardware
  

Note: We highly recommend installing our front bumper lights as well to have a completed look.

• You can buy everything together here: Front Bumper Kit
• Or individually here:
• Front Bumper Lights
• Wiring

Installation Instructions:

Written Instructions

Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek

Crawford Performance Rear Bumper Guard 2018-2023 Subaru Crosstrek

• Protects rear end and stock bumper from damage and adds a rally look to your Crosstrek

• Powder coated black for extra durability and corrosion resistance.
  Other colors available for additional cost

• Four bolt installation to sub frame provides stable mounting

• Design compatible with OEM exhaust system 

• Slider mount system provides for adjust-ability in bumper position

The Crawford Performance Subaru Crosstrek Rear Bumper Guard was inspired by theSubaru of America Crosstrek Desert Racer, with both functionality and styling in mind. Whether you are driving down the street or overlanding a trail, our off-road bumper is made to guard your Crosstrek and give you piece of mind. 

Included Components:

• One Crawford Performance Crosstrek Rear Bumper Guard 
  
• 4 sub-frame mounting plates
• 4 grade 8 carriage bolts
• 4 case hardened flange nuts
• Comes in black, other colors available by request for an additional fee.

Note: Not compatible with some hitch attachments

Installation Instructions:

Written Instructions 

Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek

Crawford Performance Hood Light Pod Kit for 2018-2023 Subaru Crosstrek

• 90 degree LED cube pods included (comes as pair) 

• Light mount brackets are included and are powder-coated for durability and corrosion resistance 

• Maintains OEM look through integrated vehicle mounting

• Includes pre-measured wiring harness

• Adds an aggressive rally style look while improving nighttime and fog visibility

• Will limit hood movement (Can still utilize 1st hood prop point)

Note: The Crawford Circuit Board is highly recommended for this kit. Giving you a clean install and mounting location for your switch. 

The Crawford Performance Hood Light / Ditch Light Pod Kit is inspired by the Subaru of America Crosstrek Desert Racer, with the simple goal of lighting up any path you choose to conquer in your Crosstrek. Our hood light brackets coupled with our 90 degree LED light pods allow for full vision from side to side of the vehicle. Providing security and assurance that nothing will take you by surprise during your night time off-roading.    

Included Hood / Ditch Light Kit Components:

• Two powder-coated hood mounting brackets 
  
• Two 90 degree LED Light pods
• Wiring harness and switch
• All necessary mounting hardware

Light Specifications:

• 90º pods are 45w each resulting in 3.75a @ 12v
• 3600 lumens from each pod cube

Installation Instructions:

Written Instructions

 Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek

If you're an off-road enthusiast who loves to take your Subaru Crosstrek on rugged terrain, you need the ultimate front-end protection. Crawford's 2018-2023 Subaru Crosstrek Front Bumper Brush Guard & Light Kit is designed to safeguard your vehicle's front end against harsh weather conditions, rocks, and other obstacles that may damage your car.

Our bumper brush guard features a durable and reliable construction that ensures maximum resistance against high impacts. It is also compatible with different LED lights that improve visibility at night. Upgrade your Subaru Crosstrek's off-road capabilities with our bumper brush guard and light kit. Here are some reasons why our kit is the best choice for your car:

1. Complete Protection: Our bumper brush guard provides an additional layer of protection against on and off-road obstacles. It protects your radiator against damage from rocks, debris, or other hazards that may damage your Subaru Crosstrek’s front end.

2. Customizable Design: The Crawford bumper brush guard is compatible with different LED lights, making it easy to customize to your preferences. It is engineered to allow you to add different lights of your choice without compromising on the quality of protection of your vehicle.

3. Durable Construction: We use the highest quality materials to make our bumper brush guard, ensuring that it will last long despite constant use.

4. Improved Visibility: Installing LED lights on our bumper brush guard improves visibility during night driving. You can attach different lighting options such as spotlights, light bars, floodlights, among others, that will significantly enhance your off-road experience.

Why Choose Crawford's Off-Road Bumper Brush Guard & Light Kit?

• Guards the front end and stock bumper from damage and adds a rugged rally look to your Crosstrek

• Powder coated for extra durability and corrosion resistance 

• Four bolt installation to sub frame requires no modifications to vehicle

• Includes three 6 inch rally style LED lights.

• Three Light Options to Choose From: 
• 6" Crawford LED Lights x 3
• 6" KC HiLiTES SlimLite LED Lights x 3
• 6" KC HiLiTES Pro6 Gravity LED Lights x 3

• Designed to work with either OEM or Crawford Skid Plates

• Call in for custom powder coat options. 

Note: The Crawford Circuit Board is highly recommended for this kit. Giving you a clean install and mounting location for your switch.  

The Crawford Performance front bumper and light kit was inspired by the Subaru of America Crosstrek Desert Racer to provide protection and improved visibility without the need to change or chop the bodywork of your Crosstrek. No modifications to the vehicle are necessary, making it a true bolt-on kit that installs in minutes. Included LED Lights provide ample night time visibility and are easily installed with the provided Crawford Front Bumper wiring harness. Increase your off-road capabilities today! 

Included Off-Road Bumper Components:

• One Crawford Performance Front Bumper
• 3 LED Lights
• Crawford Front Bumper Wiring Harness
• All necessary mounting hardware

Installation Instructions:

Written Instructions

Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek

Crawford Performance Wiring Harness for 2018-2023 Subaru Crosstrek Lights

• Custom wiring harness designed for either the hood, mirror, or bumper light fixtures featured in the Crawford Off-Road / Overland product line
• Each variant is tailored to fit the specified application making installation easier
• Wires are wrapped in protective mesh, and race style wire plugs are used to secure the connection between the power and the pods

The Crawford wiring harnesses are custom made to fit the Crawford Hood, Mirror, and/or Bumper light setups.  The incorporated mesh sheath prevents damage or tangling, and adds a clean finish to the job. Relays and fuses are integrated into the harness, and can be mounted to the Crawford Performance Circuit Board for easy access and OEM look.

Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek

Upgrade Your Subaru Crosstrek's Rear Suspension with Crawford's Billet Aluminum Rear Control Arms

Crawford Performance Billet Aluminum Rear Control Arms for 2018-2023 Subaru Crosstrek 

• Billet Aluminum Construction - Made out of 6061 aluminum

• Stronger Arms = Less concern when off-roading 

• Red anodizing protects arms from corrosion and road debris 

• Built in camber adjustability for easy alignment 

• Significant increase in strength over OEM components 

*Please note, these do not fit with Flatout Suspension's GR40 rear coilovers with external bypass.

*Also note our current iteration of these control arms do not have a light leveling sensor mount. A upcoming arm design will include this sensor mount.  

The Crawford Performance Billet Aluminum Lower Rear Control Arms were inspired by the Subaru of America Crosstrek Desert Racer to provide durability when off-roading and a sleek design for the street. The one piece, billet aluminum design is comparable to suspension components of off-road race cars that tackle grueling terrain like the Baja 1000. Adjustable heim joints allow for fine tuning and easy alignment without the need to remove and components from the vehicle. Upgraded hardware brings the kit full circle ensuring your new Crosstrek rear arms meet our off-road performance standards. Our billet rear arms are a must for any Crosstrek build. 

Included Arm Components:

• Left & Right Crawford Performance Lower Rear Arms 
• Adjustable heim joints 
• Upgraded hardware for strut and hub carrier mounting points 

Installation Instructions:

Written Instructions

Check out our Full Crosstrek Build Here:

https://crawfordperformance.com/pages/cpi-built-crosstrek